User manual ASUS P4V533-MX

[. . . ] P4V533-MX User Guide Motherboard E1376 Checklist First Edition August 2003 Copyright © 2003 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] IDE connectors (40-1 pin PRI_IDE, SEC_IDE) This connector supports the provided UltraDMA133/100 IDE ribbon cable. Connect the cable's blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraDMA133/100 slave device (hard disk drive) and the black connector to the UltraDMA133/100 master device. It is recommended that you connect non-UltraDMA133/100 devices to the secondary IDE connector. If you install two hard disks, you must configure the second drive as a slave device by setting its jumper accordingly. If you have more than two UltraDMA133/100 devices, purchase another UltraDMA133/100 cable. You may configure two hard disks to be both master devices with two ribbon cables ­ one for the primary IDE connector and another for the secondary IDE connector. 1. Pin 20 on each IDE connector is removed to match the covered hole on the UltraDMA cable connector. The hole near the blue connector on the UltraDMA133/100/66 cable is intentional. For UltraDMA133/100/66 IDE devices, use the 80-conductor IDE cable. 2. 3. NOTE: Orient the red markings on the IDE ribbon cable to PIN 1 ® SEC_IDE PIN 1 PIN 1 P4V533-MX P4V533-MX IDE Connectors 1-18 Chapter 1: Product introduction PRI_IDE 4. ATX power connectors (20-pin ATXPWR1) These connectors connect to an ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. Make sure that your ATX 12V power supply can provide 8A on the +12V lead and at least 1A on the +5-volt standby lead (+5VSB). The minimum recommended wattage is 230W, or 300W for a fully configured system. The system may become unstable and may experience difficulty powering up if the power supply is inadequate. ATXPWR1 +12. 0VDC +5VSB PWR_OK COM +5. 0VDC COM +5. 0VDC COM +3. 3VDC +3. 3VDC +5. 0VDC +5. 0VDC -5. 0VDC COM COM COM PS_ON# COM -12. 0VDC +3. 3VDC ® P4V533-MX P4V533-MX ATX Power Connectors 5. CPU and chassis fan connectors (3-pin CPU_FAN1, CHA_FAN1) The fan connectors support cooling fans of 350mA~740mA (8. 88W max. ) or a total of 1A~2. 22A (26. 64W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Lack of sufficient air flow within the system may damage the motherboard components. DO NOT place jumper caps on the fan connectors! CPU_FAN1 Rotation +12V GND ® P4V533-MX CHA_FAN1 Rotation +12V GND P4V533-MX 12-Volt Cooling Fan Power ASUS P4V533-MX motherboard user guide 1-19 6. Internal audio connectors (4-pin CD IN, AUX IN) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card. ® CD1(Black) AUX1(White) Left Audio Channel Ground Ground Right Audio Channel P4V533-MX P4V533-MX Internal Audio Connectors 7. USB header (10-1 pin USB56) If the USB ports on the rear panel are inadequate, two USB headers are available for additional USB ports. The USB header complies with USB 2. 0 specification that supports up to 480 Mbps connection speed. [. . . ] On the password box that appears, type a password composed of letters and/ or numbers, then press Enter. The message "Password Installed" appears after you have successfully set your password. To change the user password, follow the same steps as in setting a user password. Clear User Password Select this item if you wish to clear the user password. Boot Sector Virus Protection [Disabled] Allows you to enable or disable the boot sector virus protection. Configuration options: [Disabled] [Enabled] ASUS P4V533-MX motherboard user guide 2-23 2. 7 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. [. . . ]