User manual ASUS VINTAGE-PH1

[. . . ] Vintage-PH1 Barebone System E1943 First Edition March 2005 Copyright © 2005 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] Set this jumper to pins 1-2 if you are using a 4-pin fan cable plug, or to pins 2-3 if you are using a 3-pin plug. FANPWR1 12 PWM (Default) ® 23 DC mode FAN power setting ASUS Vintage-PH1 4-5 4. 4 1. Connectors Floppy disk drive connector (34-1 pin FLOPPY1) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. FLOPPY1 NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. ® PIN 1 Floppy disk drive connector 2. Primary IDE connector (40-1 pin PRI_IDE1) This connector is for an Ultra DMA 100/66 signal cable. The Ultra DMA 100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66 IDE master device (hard disk drive). If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. · Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices. · PRI_IDE1 NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. ® IDE connector 4-6 PIN 1 Chapter 4: Motherboard info 4. Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. SATA4 GND RSATA_TXP4 RSATA_TXN4 GND RSATA_RXP4 RSATA_RXN4 GND SATA3 GND RSATA_TXP3 RSATA_TXN3 GND RSATA_RXP3 RSATA_RXN3 GND SATA2 ® GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND SATA1 SATA connectors GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXP1 RSATA_RXN1 GND Important notes on Serial ATA · · You must install Windows® 2000 Service Pack 4 or the Windows® XP Service Pack1 before using Serial ATA hard disk drives. When using the connectors in standard IDE mode, connect the primary (boot) hard disk drive to the SATA1 or SATA2 connector. Refer to the table below for the recommended hard disk drive connections. Serial ATA Master/Slave connectors Connector SATA1, SATA2 SATA3, SATA4 Color Red Black Setting Master Slave Use Boot Disk Data Disk ASUS Vintage-PH1 4-7 5. CPU and Chassis Fan connectors (4-pin CPU_FAN1, 3-pin CHA_FAN1) The fan connectors support cooling fans of 350 mA~740 mA (8. 88 W max. ) or a total of 1 A~2. 22 A (26. 64 W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. Do not place jumper caps on the fan connectors! CHA_FAN1 GND +12V Rotation CPU_FAN1 GND CPU FAN PWR CPU FAN IN CPU FAN PWM ® Fan connectors Make sure that your fan power setting is correct. See page 4-5 for details. 4-8 Chapter 4: Motherboard info 6. USB connectors (10-1 pin USB56, USB78) These connectors are for USB 2. 0 ports. Connect the USB/GAME module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2. 0 specification that supports up to 480 Mbps connection speed. USB+5V USB_P6USB_P6+ GND NC ® USB56 USB 2. 0 connectors USB+5V USB_P5USB_P5+ GND USB78 USB+5V USB_P7USB_P7+ GND 1 1 Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! The USB module is purchased separately. ASUS Vintage-PH1 USB+5V USB_P8USB_P8+ GND NC 4-9 7. ATX power connectors (24-pin EATXPWR1, 4-pin ATX12V1) These connectors are for ATX power supply plugs. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. ATX12V1 GND +12V DC EATXPWR1 Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts ® ATX power connectors +3 Volts GND +12V DC +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts Important notes on the motherboard power requirements · · Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up. To power the motherboard, it is recommended that you use an ATX 12 V Specification 2. 0 power supply unit (PSU) with a minimum 350 W power rating. If you intend to use a PSU with a 20-pin and 4-pin power plugs, make sure that the 20-pin power plug can provide at least 15A on +12 V and that the PSU has a minimum power rating of 350 W. The system may become unstable or may not boot up if the power is inadequate. You must install a PSU with a higher power rating if you intend to install additional devices. · · 4-10 Chapter 4: Motherboard info 8. Optical drive audio connector (4-pin CD1) This connector is for the 4-pin audio cable that connects to the audio connector at the back of the optical drive. CD1 Left Audio Channel Ground Ground Right Audio Channel ® CD audio connector Enable the CD-IN function in the audio utility when using this connector. 9. Front panel audio connector (10-1 pin AAFP1) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC'97 audio standard. AAFP1 Azalia compliant definition GND PRESENCE# SENSE1_RETUR SENSE2_RETUR Legacy AC'97 compliant definition AGND +5VA BLINE_OUT_R BLINE_OUT_L ® PORT1 L PORT1 R PORT2 R SENSE_SEND PORT2 L Analog front panel connector We recommend that you connect a high-definition front panel audio module to this connector to use the high-definition audio features of the motherboard. ASUS Vintage-PH1 MIC2 MICPWR Line out_R NC Line out_L 4-11 1 0 . Chassis intrusion connector (4-1 pin CHASSIS1) This connector is for a chassis-mounted intrusion detection sensor or switch. [. . . ] From the password box, type a password composed of at least six letters and/or numbers, then press <Enter>. Confirm the password when prompted. The message "Password Installed" appears after you successfully set your password. To change the supervisor password, follow the same steps as in setting a user password. To clear the supervisor password, select the Change Supervisor Password then press <Enter>. [. . . ]