User manual ASUS X58L EXPRESS GATE QUICK START GUIDE

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC NOTICE · A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] · RGB (PC) / DVI (PC), · RGB (DTV) / DVI (DTV) / Component (480p, 720p, 1080i) · Video / S-Video / Component (480i) APC (Auto Picture Control) - APC adjusts the Monitor for the best picture appearance. - When adjusting picture options (contrast, brightness, color, sharpness and tint) manually, APC automatically changes to User. Press the APC button repeatedly to select the picture appearance setup option as shown below. Optimum Soft User Clear · You can also adjust APC in the PICTURE menu. · Clear, Optimum, and Soft are preset for good picture quality at the factory and cannot be changed. Manual Picture Control (User option) ( - You can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer. PICTURE APC ACC Color temp. 1. Press the MENU button and then use D /E button to select the PICTURE menu. Contrast 80 G 2. Press the G button and then use D / E button to select the desired picture option (Contrast, Brightness, Color, Sharpness, Tint). Press the G button and then use F /G Brightness 60 Color 50 Sharpness 50 Tint MENU Prev. button to make appropriate adjustments. 0 4. Press the ENTER button to save. Auto Color Temperature Control - To initialize values (reset to default settings), select the Normal option. - When adjusting color temperature options (red, green, or blue) manually, ACC automatically changes to User. Press the G D /E PICTURE APC ACC G Normal Cool button to select the PICTURE menu. Color temp. Contrast Brightness Color Sharpness Tint MENU Prev. 80 60 50 50 0 Warm User button and then use D /E button to select ACC . 3. When the number of minutes you want is displayed on the screen, press the ENTER button. To check the remaining minutes before the monitor turns off, press the SLEEP or ENTER button once. To cancel the Sleep Timer, press the SLEEP button repeatedly until zz zz --- Min option appears on the --- Min appears. 18 Plasma Display Special Menu Options Key Lock - The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing by disabling the front panel controls. - This Monitor is programmed to remember which option it was last set to even if you turn the monitor off. Press the G G D /E button to select the SPECIAL menu. SPECIAL Language Key lock ISM Method Low power G button and then use button and then use D /E D /E button to select Key lock. · With the KEY LOCK ON, the display ` button on the front panel is pressed. Key lock' appears on the screen if any Set ID Caption / Text Captions OSD Rotate MENU Prev. ISM (Image Sticking Minimization) Method - A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the Monitor's screen for a long period of time. Press the G G D /E button to select the SPECIAL menu. SPECIAL Language Key lock button and then use D /E D /E button to select ISM Method. button to select either Normal, White button and then use wash, Orbiter, or Inversion. ISM Method Low power Set ID Caption / Text Captions OSD Rotate MENU Prev. G Normal White wash Orbiter Inversion · Normal: If image sticking is never a problem, ISM is not necessary - set to Normal. · White wash White Wash removes permanent images from the screen. [. . . ] Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 · Refer to `Real data mapping 1'. Acknowledgement [t][ ][Set ID][ ][OK][Data][x] 30 Plasma Display External Control Device Setup 25. PIP Input Select (Command2:y) G To select input source for sub picture in PIP mode. Transmission [k][y][ ][Set ID][ ][Data][Cr] Data 0 : RGB 1 : Component 2 : Video Acknowledgement [y][ ][Set ID][ ][OK][Data][x] 3 : S-Video 4 : DVI 29. [. . . ]