User manual AT&T 9050

[. . . ] 2 User's Manual for Cordless Telephone Answering System 9050 Part 2 Please read Part 1 -- Important Product Information, included in your package. 9050_cover. 1AT&T 3 8/12/98, 4:14 PM © 1998 Philips Consumer Communications L. P. 848232518 Issue 1AT&T 9050_cover. 1AT&T 2 8/12/98, 4:14 PM CONTENTS INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ANSWERING SYSTEM OPERATION At the Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Handset Ringer Selection and Ringer OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 1 Press and release U until you hear "Set number of rings. " 2 Press and release S until you hear your desired setting (2, 4, 6 or Toll Saver). 4 Press and release U to set up another feature -- OR -- Press and release Y to exit. Audible Message Alert If you want the base to beep once every 10 seconds to notify you that new messages have been received, set the Message Alert to ON. (The Message Window displays ON for on, and OF for off. ) 1 Press and release U until you hear "Set audible message alert. " 2 Press and release S. 3 Press and release S until the system announces your selection (on or off). 5 Press and release U to set up another feature -- OR -- Press and release Y to exit. 15 9050_book. 1AT&T 15 8/12/98, 4:14 PM ANSWERING SYSTEM SETUP NOTE: You may stop the Audible Message Alert beep by pressing any button (except G) on the base. When new messages are received, the Audible Message Alert is activated again. Remote Access Code The Remote Access Code allows you to access features and functions of the answering system from a touch tone phone. The Remote Access Code is preset to 19, but you can change it to any two-digit number following the steps below. 1 Press and release U until you hear "Set security code. " 2 Press and release S to hear the current Remote Access Code. 3 Press and release S to increase the code by one -- OR -- Press and hold S to increase the code by ten. 5 Press and release U to set up another feature -- OR -- Press and release Y to exit. Base Ringer Setting 1 2 3 4 5 Press and release U until you hear "Set base ringer. " Press and release S. Press and release S until the Message Window displays your selection -- ON (on) or OF (off). Press and release U to set up another feature -- OR -- Press and release Y to exit. NOTE: The Base Ringer Setting does not affect the handset ringer. 16 9050_book. 1AT&T 16 8/12/98, 4:15 PM ANSWERING SYSTEM OPERATION AT THE BASE Message Window displays number of messages Set/review answering system features Use with other buttons to change settings Set/review day and time Turn answering system on or off Record a memo Skip to next message Stop/start message playback Repeat all or part of message Delete all or some messages Light goes on when answering system is on 17 9050_book. 1AT&T 17 8/12/98, 4:15 PM ANSWERING SYSTEM OPERATION AT THE BASE Answering Calls When the system is on and you've selected the Normal Announce mode, the caller hears the announcement, followed by a beep. If the message is longer than 4 minutes or shorter than 2 seconds, or if the caller is silent for more than 6 seconds, or if the system runs out of memory, the system beeps once and hangs up. If you've selected Announce Only, callers hear your announcement twice, but cannot leave a message. Call Screening/Intercept Set the volume control so you can hear the caller's message. If you decide to take the call, press P on the handset, or lift the handset of an extension phone. (If you pick up the handset or an extension phone during the announcement and the announcement does not stop right away, press * 0 on the handset or extension phone, or press Y on the base. ) Listening to Your Messages As the system plays back messages, the Message Window displays the number of the message playing. After playing each message, the system announces the day and time the message was received. After playing the last message, the system announces "End of messages. " Play all messages Press and release Y. The system announces the total number of new and old messages, then plays the new messages. Repeat entire message Press and release r after hearing the first 2 seconds. Back up to earlier message Press and release r until the Message Window displays the number of the message you want. Skip ahead to later message Press and release K until the Message Window displays the number of the message you want. [. . . ] Household appliances plugged into the same circuit as the base can sometimes cause interference. The layout of your home or office might be limiting the operating range. Try moving the base to another location, preferably on an upper floor. · · 24 9050_book. 1AT&T 24 8/12/98, 4:15 PM IN CASE OF DIFFICULTY If the phone does not ring when you receive a call: · · · · · · Make sure the handset ringer is on. Make sure the telephone line cord is connected firmly to the base and the telephone jack. [. . . ]