User manual AUDIO DESIGN IX1000.1
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AUDIO DESIGN IX1000.1. We hope that this AUDIO DESIGN IX1000.1 user guide will be useful to you.
Manual abstract: user guide AUDIO DESIGN IX1000.1
Detailed instructions for use are in the User's Guide.
[. . . ] Ideally, when connecting the source unit to the amplifier, the IX amplifier's input level switch should be set to "LO" and a low-level signal should run from the source unit's stereo RCA output to the stereo RCA input on the end panel of the amplifier using RCA interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can be delivered to the amplifier using the high-level speaker outputs on the source unit. set the input level switch on the end panel of the amplifier to "HI". Crimp and solder RCA connectors to the end of the speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the RCA Inputs on the end panel of the amplifier or simplify the installation by using a KICKER ZISL as shown below. [. . . ] The setting for this control is subjective; 80Hz is a good place to start. Bass Boost Control: The variable bass boost control on the front of the amplifier is designed to give you increased output, 0Â18dB, at 40 Hz. If you turn it up, you must readjust the input gain control to avoid clipping the amplifier. Slide the housing until it snaps into the metal bracket If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is an illuminated blue badge on top of the amplifier denoting the power state of the amp in addition to the Protection LED on the end panel of your KICKER IX series amplifier. When the blue badge is lit, this indicates the amplifier is turned on and the amplifier is functioning properly. With a Volt Ohm Meter (VOM) check the following: +12 volt power terminal (should read +12V to +16V) Remote turn-on terminal (should read +12V to +16V) Check for reversed power and ground connections. Check the following: RCA connections Test speaker outputs with a "known" good speaker. It may be necessary to replace or charge your vehicle's battery or replace your vehicle's alternator. Test for proper impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance and multiple speaker wiring suggestions). Amplifier shuts down only while vehicle is running = voltage protection circuitry is engaged. Amplifier will only play at low volume levels = short circuit protection is engaged. Check for damaged RCA (or speaker input) cable Check the routing of RCA (or speaker input) cable Check the source unit for proper grounding Check the gain settings and turn them down if they are set too high. Reverse a speaker connection from positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out of phase. KICKER amplifiers are engineered to be fully compatible with all manufacturers' head units. Some head units may require additional grounding to prevent noise from entering the audio signal. If you are experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the head unit to the chassis will remedy this issue. Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The KICKER Coaxial and Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms) and work with any amplifier designed to operate at a four ohm load. If you want to use two KICKER Coaxial or Component speakers on a single channel of your amplifier, wire the speakers in series. This will improve the sound quality, lower the total harmonic distortion and lessen the thermal load at the amplifier. This may prevent an amplifier from shutting down due to over-current protection circuitry. [. . . ] You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal. If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER Customer Service Department at (405) 624-8510 for a Return Merchandise Authorization (RMA) number. Package only the defective items in a package that will prevent shipping damage, and return to: Stillwater Designs, 3100 North Husband St, Stillwater, OK 74075 The RMA number must be clearly marked on the outside of the package. The return of functioning items increases your return freight charges. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE AUDIO DESIGN IX1000.1
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AUDIO DESIGN IX1000.1 will begin.