User manual AUDIO DESIGN QS60.2

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AUDIO DESIGN QS60.2. We hope that this AUDIO DESIGN QS60.2 user guide will be useful to you.


AUDIO DESIGN QS60.2 : Download the complete user guide (1658 Ko)

Manual abstract: user guide AUDIO DESIGN QS60.2

Detailed instructions for use are in the User's Guide.

[. . . ] In this configuration, the amplified signal from your source unit or amplifier should be wired to the + and - terminals indicated on the INPUT jumper. The QS crossover can also be configured for bi-amp wiring by removing (or simply not installing) the INPUT jumper. To use the bi-amp configuration, you must connect two amplified signals to each crossover (you will need at least four amplifier channels). install one of the included tweeter outputlevel jumpers (0 dB , +3 dB , or +6 dB) to adjust the tweeter output level. [. . . ] For angled mounting applications choose a flat location on the panel with space behind the panel to allow room for the mounting nut, motor structure, tweeter post, and back angle ring. After checking the clearances, cut a 1-13/16" (46mm) diameter mounting hole in the panel. Then place the wire and tweeter through the front angle ring and into the panel. Next, place the wire through the back angle ring, place the back angle ring over the rear of the tweeter, and line-up the narrow part of the front angle ring for the preferred angle of operation. Place the wire through the mounting nut and loosely tighten the mounting nut around the tweeter. Rotate all the parts in unison until the tweeter is angled in the desired direction. Mount the crossover in a location that is easy to access for wiring and tweeter output level adjustment. If you must mount the crossover in the car door, exercise caution as water can accumulate in the bottom of the door. (mounted inside door panel) tweeter mounting hole to tweeter lead wires From amplifier or source unit If factory speaker wiring is not available in your desired location, it may be necessary to run speaker wire through the door jamb. The speaker wire should be kept away from sharp edges and avoid the possibility of getting pinched by the door. an existing grommet in the door jamb is the ideal place to run the speaker wire. If the factory hole and grommet do not exist or are inaccessible, you must drill a hole to run the speaker wire through the door jamb. Be careful not to drill into other wiring or existing door mechanisms. Any time a wire is run through a hole, it is necessary to insert a rubber or plastic grommet to protect the wire from damage. KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is warranted for ONE (1) YEAR from date of original purchase with receipt. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction during the warranty period, KICKER will repair or replace (at its discretion) the defective merchandise with equivalent merchandise at no charge. Discontinued products may be replaced with more current equivalent products. This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. [. . . ] Repeated returns for the same damage may be considered abuse o Any cost or expense related to the removal or reinstallation of product o Speakers damaged due to amplifier clipping or distortion o Items previously repaired or modified by any unauthorized repair facility o Return shipping on non-defective items o Products with tampered or missing barcode labels o Products returned without a Return Merchandise Authorization (RMA) number o Freight Damage o The cost of shipping product to KICKER o Service performed by anyone other than KICKER Delays may be incurred if lack of replacement inventory or parts is encountered. Any questions can be directed to the KICKER Customer Service Department at (405) 624-8510. Contact your International KICKER dealer or distributor concerning specific procedures for your country's warranty policies. To get the best performance from your new KICKER speakers, we recommend using genuine KICKER accessories and wiring. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AUDIO DESIGN QS60.2




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AUDIO DESIGN QS60.2 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.