User manual BBE SOUND 702

[. . . ] AC Receptacle - Check to make sure that the AC receptacle holds the power cord plug firmly and securely. If the power cord plug is loose, contact your electrician to replace the defective and unsafe AC Foreign Objects - Be careful that foreign objects and liquids do not enter the enclosure through openings. Use a damp cloth for cleaning. SERVICE Unplug the appliance from the wall outlet and consult qualified service personnel when: · the power cord or the plug has been damaged. · the appliance does not appear to operate normally or exhibits a marked change in performance. [. . . ] The BBE Process is so unique that 42 patents have been awarded by the U. S. Patent Office. PROdUCT dESCRIPTION The BBE 382i is a dual channel, single rack space device for use in -10dBu unbalanced level applications. There are two separate channels that share the same front panel Lo Contour control and Process controls for ganged-stereo operation. A single function button switches the BBE process on or off in both channels, which is useful for comparing the processed sound to the unprocessed sound. An LED next to the function button glows green when the BBE process is on and red when the process is off. The Lo Contour control is for adjusting the level of phase corrected low frequencies in the program material. The Process control is for adjusting the level of phase corrected high frequencies in the program material. APPLICATIONS Music and P. A. Systems The BBE Sonic Maximizer is a welcome addition to any live sound P. A. system because the BBE circuit dramatically improves the clarity and intelligibility of vocals and musical instruments. Night club and mobile DJ systems will also benefit greatly from the BBE Process, with more depth, detail and punch over the entire mix. When using in conjunction with an equalizer, the Sonic Maximizer should be added after the equalizer in the signal chain. When the switch is pushed in, the process is on and the indicator LED is green. When the switch is out, the process is off and the indicator LED is red. POWER: This switch controls primary power to the BBE 382i. Rear Panel Connections 1. FUSE: Insert a flat blade screwdriver into the fuse holder located in the bottom portion of the AC Power Cord inlet. Carefully pry the fuse holder free from its compartment to access fuse. AC SELECTOR SWITCH: This switch is set at the factory to match the AC power requirements of the country where it will be sold and should only be adjusted by a qualified technician. OUTPUT CHANNEL B: Each channel is equipped with an unbalanced 1/4" line level output jack that can deliver up to +20dBu into 1K Ohms. INPUT CHANNEL B: Each channel is equipped with an unbalanced 1/4" -10dBu line level input jack. CHANNEL A: These connections function the same as CHANNEL B. 5 SPECIFICATIONS Frequency Response process mode bypass mode Program controlled 5Hz to 30kHz +/-0. 5dBu, -10dBu input less than 0. 1% at -10dBu input, 20-20kHz +20dBu (may vary due to control settings) 47k Ohms, unbalanced 1/4" phone jack or RCA jack 1k Ohms, unbalanced 1/4" phone jack or RCA jack -45dBu for maximum process +12dBu boost at 5kHz +12dBu boost at 50Hz U. S. , Canada & Japan models: 120VAC, 50/60Hz, 8 WATTS Power Requirements Standard model: 220VAC, 50/60Hz, 8 WATTS Fuse Dimensions Shipping Weight * 0dBu = 0. 775mVrms Note: Due to continuing product improvement, specifications and design are subject to change without notice. THD in process mode Maximum Output Input Impedance Output Impedance Sensitivity Maximum Process Lo Contour Replace with 250VAC, 200mA fastblow type fuse 19"(W) x 5. 5"(D) x 1. 7"(H) 6. 5 lbs. The BBE Sonic Maximizer is a line level signal processor and is to be connected prior to the power amp in any audio system. Significant damage may be inflicted to the bbe sonic maximizer or any subsequent component in the system in the event the output of a power amp is connected directly to the input of the BBE Sonic Maximizer. LIVE APPLICATION: NON-POWEREd MIXER Connect the BBE 382i to the output of the mixing console or external equlization, if used. The output of the BBE will drive either a crossover or a power amplifier directly. MAIN OUTPUTS CAUTION: 115V AC SELECTOR SWITCH FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE ONLY WITH SAME TYPE 0. 2A 250V FUSE WARNING: ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE T 0. 2A 250V FUSE LINE FREQUENCY: 50-60Hz POWER CONSUMPTION: 8 WATTS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE! CHANNEL B OUTPUT INPUT CHANNEL A OUTPUT INPUT ® AVIS: RISQUE DE CHOC E L E C T R I C N E PA S OUVRIR! CALIFORNIA, USA MODEL 382i US PATENT NO. [. . . ] During this period, we will repair units free of charge providing that they are shipped prepaid to BBE Sound, Inc. , 5381 Production Drive, Huntington Beach, CA 92649. All charges related to non-UPS shipping, including customs clearance, will be billed. The warranty will be honored for the longer of either 90 days from the date of any service or the remainder of the original 5 Year factory warranty. The equipment has been electrically damaged by improper connection or attempted repair by the customer or a third party. [. . . ]