User manual BEGLEC DYNAMO VERSION 1.0

[. . . ] It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual. CAUTION: To reduce the risk of electric shock, do not remove the top cover. The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. [. . . ] In the event of serious operating problems, stop using the fixture and contact your dealer immediately. The housing and the lenses must be replaced if they are visibly damaged. Due to safety reasons it is prohibited to make unauthorized modifications to the unit. Don't use the effect in the presence of persons suffering from epilepsy. Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook. This input receives instructions from a DMX-controller or from another Dynamo light effect when used in master/slave mode. DMX output: 3pin female XLR-connector used to connect the Dynamo with the next unit in the DMX chain or with another Dynamo when used in master/slave mode. Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety. Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The device should be installed out of reach of people and outside areas where persons may walk by or be seated. Before rigging make sure that the installation area can hold a minimum point load of 10times the device's weight. Always use a certified safety cable that can hold 12times the weight of the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails. The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!Don't cover any ventilation openings as this may result in overheating. The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal. Standalone 1unit: Just connect the unit to the mains and put on some music. Two or more units in master/slave setup: Connect 2 or more units together using good quality balanced XLR microphone cables . [. . . ] You need to "daisy chain" your DMX controller and all the connected light effects with a good quality XLR M/F balanced cable. To prevent strange behavior of the light effects, due to interferences, you must use a 90 to 120 terminator at the end of the chain. Each light effect in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode. How to set the DIP-switches to obtain the right starting address: On the back of the Dynamo you will see that each of the first 9 DIP-switches corresponds to certain value: Dip #1 #2 #3 #4 #5 #6 #7 #8 #9 Value 1 2 4 8 16 32 64 128 256 You can combine the values of these switches to become any starting address between 1 and 512: Begin address = 01 switch 1=ON values: 1 Begin address = 05 switch 1+3=ON values: 1+4 = 5 Begin address = 09 switch 1+4=ON values: 1+8 = 9 Begin address = 13 switch 1+3+4=ON values: 1+4+8 = 13 Begin address = 62 switch2+3+4+5+6=ON values: 2+4+8+16+32 = 62 DMX-CONFIGURATION OF DYNAMO, DYNAMO 250 & DYNAMO 250 BARREL: Make sure the area below the installation place is free from unwanted persons during servicing. [. . . ]