User manual BELSON BP8410

[. . . ] 12) Learn to get to know the parts which make up your dishwasher, you will use it better for it. This is where you will find the description of the controls and the internal parts. 13) This page includes useful tips to help you load your dishwasher correctly and make the most of all the available space. 14) After loading the dishes, you need to select the right wash cycle and measure out the correct dose of detergent and rinse aid. [. . . ] (If your dishwasher is fitted with a “low rinse aid” indicator light, fill the container up when the indicator light flashes or lights up). You can adapt the amount of rinse aid used by the dishwasher: regulate the adjuster F which you will find under lid C. If drops of water remain on the dishes or spotting occurs, turn the dosage adjuster to a higher setting. If, on the other hand, the dishes have white streaks, then turn the dosage adjuster down to a lower setting. Warning Three-in-one dishwasher tablets are now available on the market, and combine detergent, salt and rinse aid all in one. If the water in your area is hard or very hard, we still recommend you pour extra salt into the relevant dispenser to prevent the formation of white streaks on your dishes or on the interior of the appliance. Using a three-in-one product means it is no longer necessary to put rinse aid into the relevant container. If you want to achieve perfectly dry dishes, you may add rinse aid as long as the dosage adjuster is set to no. In any case, please read the manufacturer's instructions on the packet. ARISTON DISHWASHER - Instructions for installation and use 15 D ISHWASHER Select the right wash cycle A wash cycle for every degree of soil Dishwasher washing guarantees your dishes will be cleaned in a hygienic setting for safer, cleaner results. Salt, rinse aid, the right amount of detergent and the correct wash cycle: this is the formula to get the best results and to keep your dishwasher in shape Select the right wash cycle for your dishes. Special plastic elbow provided (see correspond to those stated on the This electric household figure) to position it in the best rating plate located on the stainless appliance should be connected possible way. The part of the pipe steel inner door of the appliance to the water mains using the marked with the letter A should be and that the electrical system to cold water supply hose between 40 and 100 cm above the which the dishwasher is connected provided with the appliance ground. Do not use a different The pipe should not be immersed indicated on said rating plate. A Connect the cold water supply Only now can you plug the hose to a 3/4 gas threaded conappliance into a socket nection, and connection taking care provided with an efficient earth to screw it tightly onto the tap. Connection (the system's If the water pipes are new or have earthing is a guarantee of safety not been used for an extended provided for by law, make sure your system has it). If the power socket to which the appliance is connected is not compatible with the plug, replace it with a suitable plug rather than using adapters or multiple plugs as these could cause overheating or burns. Check the power supply wire on a regular basis; if it is damaged, we recommend you have it replaced by an authorised technical Assistance service centre. The plug The dishwasher plug must be accessible so that maintenance can be done safely. The special plastic elbow should be fastened firmly onto the wall to prevent the drain hose from moving and allowing water to spill outside the drain. 18 ARISTON DISHWASHER - Instructions for installation and use If you have a problem, read this Troubleshooting D ISHWASHER Safety within your home 1. Dispose of the packaging material carefully (follow the instructions on how to divide your rubbish up provided by your local Council) After removing the packaging, check to make sure your appliance is intact. [. . . ] For this reason, it is a good idea to remove the larger food particles trapped inside the cup “C” and the semi-circular filter A after each wash; pull the cup handle upwards to remove them. The entire filter assembly should be cleaned thoroughly once a month: cup C + semi-circular filter A + cylindrical filter B. Reassemble the filter parts (as shown in the figure) and reinsert the whole assembly into the dishwasher. Improper replacement of the filters may reduce the efficiency of the wash and even damage your dishwasher. [. . . ]