User manual BOSCH SMD 53M74EU/80 SUPPLEMENT

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSCH SMD 53M74EU/80. We hope that this BOSCH SMD 53M74EU/80 user guide will be useful to you.


BOSCH SMD 53M74EU/80 SUPPLEMENT: Download the complete user guide (740 Ko)

Manual abstract: user guide BOSCH SMD 53M74EU/80SUPPLEMENT

Detailed instructions for use are in the User's Guide.

[. . . ] This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Sears, Roebuck and Co. , D/817 WA, Hoffman Estates, IL 60179 If you want your water softener professionally installed, talk to your Sears Salesman. He will arrange for a prompt, quality installation by Sears Authorized Installers. SEARS INSTALLATION POLICY All installation labor arranged by Sears shall be performed in a neat, workmanlike manner in accordance with generally accepted trade practices. Further, all installations shall comply with all local laws, codes, regulations, and ordinances. [. . . ] Hold a broom handle, or like tool, up to the softener as shown in FIG. Make a pencil mark on the handle, 1 or 2 below the top height of the rim, as shown. If a hard object is felt before the pencil mark gets to the top of the tank, it's most likely a salt bridge. Do not try to break the salt bridge by pounding on the outside of the salt tank. 9 SALT BRIDGE push tool into salt bridge to break 1" ­ 2" pencil mark broom handle salt salt bridge water level 14 SECTION 3 3B. CARE OF YOUR SOFTENER KEEPING THE WATER SOFTENER CLEAN NOTE: Never use cleaners having ammonia or abrasives. They may scratch and dull the surface. COVERS To keep your new Sears water softener looking nice, apply a coat of paste wax and repeat once a year. This small unit moves brine from the salt storage tank to the resin tank during regeneration. If it becomes plugged with sand, silt, dirt, etc. , the softener will not work and you will get hard water. To get to the nozzle and venturi, remove the softener top cover. Be sure the softener is in service cycle (no water pressure at nozzle and venturi). Lubricate the o ring seal with silicone grease or Vaseline and place in position. 10 CLEANING THE NOZZLE & VENTURI Cap O­ring Seal Screen Support Screen Nozzle & Venturi Gasket NOTE: Be sure holes in the gasket align with the holes at the bottom of the nozzle & venturi housing. Often, you will find what's wrong yourself and you won't have to call and wait for service. If, after making the checks, your softener still does not work right, call your Sears Service Department, or call toll free, number 1-800-426-9345 for telephone assistance. NOTE: 1. If an error code is not dispIayed, press and hold the SELECT button until (example: 000- -) shows in the display. If any other SR number shows, the softener computer is working on incorrect input and this would probably be the cause of the problem. Then, press SELECT to return a flashing 12:00 AM display, and reset the timer on page 6. PROBLEM No soft water CAUSE CORRECTION Water hard sometimes Faucet or fixture may be plumbed to From the outlet of the water softener, trace the water flow hard water paths in your house pipes. If soft water is not directed to a faucet or fixture where it is wanted, consult a plumber. To conserve salt, the installer may have isolated some fixtures (outside faucets, toilets, etc. ) from soft water. No salt (or salt bridged) in the storage Refill with salt, or break the salt bridge (page 14). Press tank ON/OFF-HOLD (RECHARGE NOW) button and hold for 3 seconds to start a regeneration (see page 10). Transfomer unplugged at the wall Check for loss of power due to any of these and correct. [. . . ] Fill flow continues to the brine valve, and into the salt storage tank. Soft water is still available to the house lines. 24 SECTION 5 SERVICE TECH. WATER FLOW THROUGH THE SOFTENER VALVE BRINING AND BRINE RINSE CYCLES venturi drain nozzle brine from salt storage tank bypass hard water to valve outlet from Valve Inlet (hard water) After fill, timer/switch action allows the motor to turn the rotor and disc into BRINING position. Suction, created by the nozzle and venturi, draws brine from the salt storage tank and injects it into the resin bed via the bottom distributor. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSCH SMD 53M74EU/80




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSCH SMD 53M74EU/80 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.