User manual CANDY CTI 46 B

[. . . ] The size of these openings must be at least 300 cm2 and placed as shown in fig. When a 75 cm hob is fitted over a built in oven, the latter must be fan cooled. FIG. ONLY INSTRUCTIONS FOR THE INSTALLER The following information is intended for qualified and competant persons only who will ensure that your appliance is installed correctly. All current legislation concerning the installation of Gas appliances must be observed by the installer* * For the U. K. [. . . ] It is possible to use other types of gas after carrying out simple modifications. Warning: If gas can be smelt in the vicinity of this appliance turn off the gas supply to the appliance and call the engineer directly. Do not search for a leak with a naked flame. 42 GB IE ELECTRICAL CONNECTION Check the data on the rating plate, located on the outside of the unit, to ensure that the supply and input voltage are suitable. If this regulation is not complied with, the Manufacturer will not be responsible for any damage caused to persons or property. If a plug is not already attached, fit a plug appropriate to the load indicated on the rating plate. Where the Hob is connected direct to the electricity supply, a circuit breaker must be fitted with at least a 3 mm contact spacing when in the open position. If the power supply cord is damaged this is to be replaced by a qualified engineer so as to prevent any potential risk. The earth wire ( green a yellow coloured) must be at least 10 mm longer than the live and neutral wires. The section of the cable used must be of the correct size in relation to the absorbed power of the hob. Please check rating plate for the power details and ensure that the power supply cord is of the type H05RR-F, H05VV-F, H05V2V2-F. MAINS SUPPLY LIVE EARTH L BROWN WIRE GREEN/YELLOW WIRE BLUE WIRE POWER CABLE NEUTRAL N GAS CONNECTION These instructions are for Fitters qualified for installation of equipment in line with the relevant national standard. All work must be carried out with the electricity supply disconnected. Using a small Terminal type screwdriver the regulating screw can be adjusted as in Fig. Turning the screw clockwise reduces the gas flow, whilst turning it anticlockwise increases the flow Use this adjustment to obtain a flame of approximately 3 to 4 mm in length and then replace the control knob. When the gas supply available is LPG (Bottle gas)- the screw to set the idle flame must be turned (clockwise) to the end stop. 9 IE GB 45 When you have carried out the new gas regulation, replace the old gas rating plate on your appliance with one (supplied with hob) suitable for the type of gas for which it has been regulated. USE OF HOB USER INSTRUCTIONS This appliance must only be used for the purpose for which it is intended, domestic cooking, and any other use will be considered improper and could therefore be dangerous. The Manufacturer will not be responsible for any damage or loss resulting from improper use. USING THE GAS BURNER To ignite the burners, place a lighted taper close to the burner, press in and turn the control knob anti-clockwise. If the burners have not been used for a couple of days, wait for a few seconds before lighting the burner, this will allow any air present in the pipes to escape. For appliances fitted with electronic ignition carry out the following: push in and turn the knob anticlockwise to the 5 symbol. For hobs fitted with automatic ignition simply push in and turn the knob to the 5 symbol. The ignition system will continue to generate sparks as long as the gas tap is being pressed. If the burner is not ignited within 5 seconds, turn the knob to the 0 position and repeat the operation. For models fitted with a safety tap (which cuts-off the flow of gas if the flame is accidentally extinguished) the burners are ignited ad described above, but care must be taken to keep the knob pressed in for 5 or 6 seconds after the flame is ignited. [. . . ] Hotplates should only be cleaned with a cotton cloth coated with vaseline or seed oil. GB IE 49 Never use abrasives, corrosive detergents, bleaching agents or acids. Avoid any acid or alkaline substances (lemon, juice, vinegar etc. ) on the enamelled, varnisched or stainless steel sections. To restore their original shine, use a household stainless steel cleaner. (For all hobs): "WARNING - do not use steam cleaners to clean the hobs". AFTERCARE Before calling out a Service Engineer please check the following: -- that the plug is correctly inserted and fused; -- that the gas supply is not faulty. [. . . ]