User manual CANDY MIC202

[. . . ] This oven is equipped with a cord having a grounding wire with a grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing an escape wire for the electric current. WARNING - Improper use of the grounding plug can result in a risk of electric shock. The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE GROUNDING PIN FROM THE PLUG. [. . . ] Rear exhaust: If a rear or horizontal exhaust is to be used, care should be taken to align the exhaust with the space between the studs, or wall should be prepared at the time it is constructed by leaving enough space between wall studs to accommodate exhaust. Maximum duct length: For satisfactory air movement, the total duct length of 3-1/4" X 10" rectangular or 6" diameter round duct should not exceed 140 feet. present additional resistance to air flow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total length, add the equivalent lengths of all transitions and adapters plus the length of all straight duct sections. Figure 4 shows the approximate feet of equivalent length of some typical ductwork parts. Use the values in parentheses for calculating air flow resistance equivalent, which should total less than 140 feet. Figure 4 5 TOOLS RECOMMENDED FOR INSTALLATION · Phillips Screwdriver · Electric Drill · 1/2", 5/8" and 3/32" Drill Bits · Saw to cut exhaust opening (if needed) · 1-1/2" Wood Bit or Metal Hole Cutter (if metal cabinet is used) · Scissors · Pencil · Measure · Tape · Protective Drop Cloth for product and range -you may also use carton for protection 6 INSTALLATION HARDWARE The INSTALLATION HARDWARE items 1-7 are in a small bag. ITEM 1 2 3 4 5 6 7 8 9 NAME Wood Screw 5 X 30 mm Toggle Bolt #10 - 24 X 50 mm Top Cabinet Screw 5 X 60 mm Flat Washer 5 mm diameter Cord Holder Grommet Tapping Screw 4 x 12 mm Exhaust Damper Assembly Charcoal Filter QUANTITY 6 4 2 2 1 1 1 1 1 PART CODE XTSSD50P35000 LX-BZ0195WRE0 XBRSD50P60000 XWHSD50-16300 LX-MZB001MRE0 LBSHC0040MRE0 XOTSD40P12000 FFTA-B003MRK0 / FFTA-B005MRK0 PFIL-B004MRE0 Figure 5 3 7 PREPARATION OF THE OVEN 1. Open the bottom of the carton, bend the carton flaps back and tilt the oven over to rest on plastic foam pad. Lift carton off oven and remove all packing materials, Installation Instructions, Wall Template, Top Template, Charcoal Filter, Turntable and Turntable Support; however, DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the ceiling in the oven cavity. Check the oven for any damage, such as misaligned or bent door, damaged door seals and sealing surfaces, broken or loose door hinges and latches and dents inside the cavity or on the door. If there is any damage, do not operate the oven and contact your dealer or CANDY AUTHORIZED SERVICER. Replace the Fan Cover Bracket by sliding it into the slits in the same direction as the arrow on the Fan Cover Bracket. Make sure the fan blades are visible through the top openings in the oven before proceeding. Attach the Fan Cover Bracket to unit with 3 screws, which were removed in Step 1 above. Attach the Exhaust Damper Assembly 8 to the fan cover on the top of the outercase cabinet after mounting the oven. To attach the Exhaust Damper Assembly, refer to MOUNTING OVEN TO THE WALL, Step 7 on page 7. Figure 14 9 OVEN INSTALLATION THIS OVEN CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO THE MOUNTING INSTRUCTIONS FOUND ON BOTH TEMPLATES. THE NEXT STEP IS TO READ AND FOLLOW MOUNTING INFORMATION ON BOTH TOP CABINET AND WALL TEMPLATES. Separate 4 Toggle Bolts 2, packed in the INSTALLATION HARDWARE, from the Toggle Nuts. Use Toggle Bolts to attach Mounting Plate through the holes at A, B, C and D; UNLESS THOSE HOLES ARE LOCATED ON THE STUD. Insert one Toggle Bolt into A, B, C and D where appropriate (these correspond to the holes of the Wall Template) and put the Toggle Nuts onto the Toggle Bolts. Position the Mounting Plate with the Toggle Bolts attached at the wall location and insert Toggle Nuts and Bolts through the holes in the wall with the Toggle Nuts closed. NOTE: Before insertion, be sure you leave a space more than the thickness of the wall between the Mounting Plate and the end of each of the Toggle Nuts (in the closed position). [. . . ] Hook the three lower tabs of Louver E into the slits of the oven faceplate. Then insert three upper tabs of Louver E into the slits of the oven faceplate. NOTE: The upper middle tab should be inserted between the oven faceplate and the outercase cabinet. Figure 18 Louver (cross section) Upper Tabs Or Louver F (some models) 4. Insert the top tabs of hood Louver F into the 3 openings on the cavity faceplate holding Louver F at a slightly outward tilt. [. . . ]