User manual CANDY PL2250XX

[. . . ] This appliance must be installed in accordance with applicable regulations and should only be used in well-ventilated locations. Suitable location A gas-powered cooking appliance produces heat and humidity in the area in which it is installed. For this reason you should ensure good ventilation either by keeping all natural air passages open or by installing an extractor hood with an exhaust flue. Intensive and prolonged use of the appliance may require extra ventilation, such the opening of a window or an increase in speed of the electric fan, if you have one. [. . . ] The cables should be 1 mm2 section, also, the maximum external diameter of the cable should not be greater than 7 mm. To adapt the Hob for use with different types of gas, carry out the following instructions: -- remove the grids and burners -- insert the hexagonal spanner (supplied) into the burner support (Fig. 5) -- unscrew the injector and replace it with one suitable for the gas to be used (see Table of gas consumption) -- carry out regulation of the burner. G20/G25 Working burner large back right large front left medium small double ring maxi G30 G20/G30 Qn kW 2, 65 2, 95 1, 5 1, 1 3, 3 3, 3 l/h G20 252 281 143 105 314 314 g/h G30 193 215 109 80 238 238 g/h G31 189 211 107 79 236 236 The rating plate on the hob shows the type of gas with which it is designed to be used. It is possible to use other types of gas after carrying out some simple modifications. A) Connection to the gas supply -- connection to the mains gas supply or gas cylinder should be carried out according to the relevant national standards, after having checked that it is regulated for the type of gas with which it will be supplied. If it is not correctly regulated follow the instructions in the paragraph entitlet «Adaption for different types of gas». For liquid gas (cylinder gas) use pressure regulators which comply with the relevant national standards. : for safe operation, economic use of energy and to ensure greater durability of the appliance, make sure that the supply pressure conforms with the values shown in the table on page 38 -- Connection to a rigid pipe (see instruction on page 44) Connection to the gas supply should be done without putting any kind of stress on the appliance. -- Connection to a flexible steel pipe (see instructions on page 44) The junction of the gas pipe with the appliance is a 1/2" gas tapered thread connection. Use only pipes, washers and sealing washers which comply with the relevant national standards. The fitting of these pipes should be done to that their maximum length, when fully extended, should not exceed 2000 mm. : carry out a final check for leaks on the pipework using a soapy solution. Also, make sure that the flexible pipe cannot come into contact with a movlng part of the cabinet (eg, a drawer) and that it is not situated where it could be damaged. For maximum efficiency from the burners, the correct combustion of the flame is necessary (see table of gas consumptions quota "X"). If there is insufficient air, the flame will be uneven with yellow tips (Fig. If there is too much air, the flame will be very short and bright (Fig. In these cases the combustion must be adjusted by re-fitting the carburation tube to the Venturi (where there is insufficient air) or removing the carburation tube (in the case of too much air). To position the carburation tube, the fixing screws must be loosened, and retightened when the satisfactory combustion is obtained. This appliance must only be used for the purpose for which it is intended, domestic cooking, and any other use will be considered improper and could therefore be dangerous. The Manufacturer will not be responisble for any damage or loss resulting from improper use. To ignite the burners, place a lighted taper close to the burner, press in and turn the control knob anti-clockwise. [. . . ] To protect the glass lid from damage and in the interests of safety, the burners/plates must be turned off and the burner/pan support/plate area must be cool before closing the lid down. For the best use of the electric hotplates and to minimise energy consumption, the following recommendations should be noted. The Manufacturer will not be responsible for any inaccuracy resulting from printing or transcript errors contained in this brochure. We reserve the right to carry out modifications to products as required, including the interests of consumption, without prejiudice to the characteristics relating to safety or function. [. . . ]