User manual CARVIN C2440

[. . . ] This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompa nying the appliance. LIMITED WARRANTY Your Carvin product is guaranteed against failure for 1 YEAR unless otherwise stated. Carvin will service and supply all parts at no charge to the customer providing the unit is under warranty. Carvin assumes no responsibility for horn drivers or speakers damaged by this unit. This warranty does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions. [. . . ] Each channel can be assigned to the 12, 3-4, and L-R Faders in stereo pairs. This feature allows the operator to group certain channels (such as the channels used to mic an entire drum kit) and assign them to one pair of the master faders in the 1-2, 3-4 sub group. This sub-mixing feature decreases the number of channel faders that need to be adjusted. channel is great for a third main mix, a subwoofer out or in the case of a main mono mix, group 1-4 and L-R creates a 6 buss console. 28. PHONES JACK 1/4" stereo jack for headphone or control room output. 20. CONTROL ROOM SELECTION SWITCHES Use these switches to select what is heard through the headphones and control room jacks. TAPE IN TO L-R SWITCH This switch assigns the source coming from the RCA TAPE IN connections to the L-R mix. 16. AUDIO TAPER FADERS Slide all faders down when connecting your inputs. Calibrated 60mm faders with audio taper are featured for smooth fade-outs. 21. PFL RED LED Indicates that the headphone, control room, and meters are monitoring the channels where the PFL is switched on. 31. TAPE IN CONTROL This adjusts the level of the source coming from TAPE IN. 32. CONTROL ROOM JACK This 1/4" stereo connection is for headphones or connecting a control room power amp & studio reference monitors. 22. L-R SUB TO CENTER SWITCHES Assignes the LEFT-RIGHT mix to the CENTER Fader. MASTER SECTION 17. GROUPS 1 - 4 Once a channel has been assigned to one of the 4 groups (see 15), 60mm faders control the level of each group. 23. PHONES CONTROL The PHONES control sets the desired level of the PHONES jack for monitoring through headphones. 41 40 39 38 37 33. TAPE OUT SOURCE This switch changes the tape out source from L-R to AUX 3-4. This is a great feature for 2 track live recording where a different mix is needed from the L-R house mix 34. STEREO RETURNS 37 36 35 34 33 32 31 30 29 28 27 Each return contains a master level for the L-R mix and a master level for the AUX (monitor mix) with RETURN 1 & 2 going to AUX 1, and 3 & 4 going to AUX 2. 35. TAPE IN-OUT Stereo RCA jacks for connecting a tape recorder or CD player. 36. LEFT / RIGHT XLR & 1/4" CONNECTORS This set of balanced and unbalanced connectors are for connecting the main mix to external power amp(s). 25 24 38. 1/4" GROUP OUTPUT CONNECTORS 1 through 4 offer output of each individual GROUP fader for use in multitrack recording or connecting additional power amps for stage monitors or main house speakers. 23 22 21 20 39. Or, use these sends to drive additional power amps for stage monitors. The C2440 provides balanced 1/4" outputs for long cable runs on AUX SENDS 1 & 2. 17 18 19 40. [. . . ] The channel signal coming from the microphone preamplifier will be forced to go through the external equipment before it can continue back through the channel re-entering before the channel tone controls. Most external equipment is not set up for the TRS plug directly so an adapter cable is required. The adapter cable will have on one end the TRS plug and two mono plugs either male or female, on the other end. The two plugs each have the ground connected to the sleeve, one has the return on its tip and the other has the send on its tip. [. . . ]