User manual CARVIN SRS65A

[. . . ] CARVIN ENGINEER DATA SRS6. 5/SRS6. 5A STUDIO MONITOR INSTRUCTIONS FIG. 1 CONTOUR FLAT PRECAUTIONS 1) DO NOT EXCEED THE POWER RATING ON THE SRS6. 5 marked on the rear connect plate. 3) DISTORTION from power amps will destroy drivers much faster than clean power. [. . . ] The front ported design ensures that you can place the SRS monitors anywhere in the room without unwanted low frequency side affects, which is a problem with rear ported enclosures. FIG. 2 SRS6. 5A ACTIVE POWERED Active Biamp: Low 70w RMS, High 30w RMS Amp Response: 20 to 20 k Hz, THD . 03% Enclosure Response: 50 to 20 k Hz, ± 3 dB Inputs SRS6. 5A: Bal. XLR, 12dB attenuation pad, 90-250VAC, 50-60 Hz, LED power indicator Woofer Enclosure Type: Front Ported Box Protective Coating: Black DuratexTM SRS6. 5A: 9. 25"W x 11. 75"D x 14. 75"H, 23 lbs. RECEIVING INSPECTION INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during shipping. If any damage is found, please notify the shipping company & CARVIN. In the event you have to re-ship your unit, always use the original carton and packing material. CARVIN and the shipping company are not liable for any damage caused by improper packing. Please allow several days for the rest of your order to arrive before inquiring. RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual for your records. Keep your portion of the card and return the portion with your name and comments to us. SRS6. 5 PASSIVE Inputs SRS6. 5: Gold 5-way binding posts Enclosure Response: 50 Hz to 20 kHz, ± 3 dB Sensitivity: 92. 5 dB SPL, 1 Watt @ 1 meter Power Handling: 125w continuous Recommended Amp: 50 to 150 watts Nominal Impedance: 8 SRS6. 5: 9. 25"W x 9"D x 14. 75"H, 21 lbs. CONNECTING THE SRS6. 5 AND THE SRS6. 5A Connecting to the SRS6. 5 is via positive and negative gold plated binding posts located on the rear jackplate. Carvin's standard cable for hookup is the PH series cable used in with the AD42 speaker cable adapter. Connect the SRS6. 5A powered monitors directly to your mixer or source device's output with a balanced XLR cable. Connect the AC power cord to a standard 120v or 230v power receptacle. Serial No. _____________________ Invoice Date________________ SRS6. 5 PASSIVE MODEL 76-06508A 0302 SRS6. 5A ACTIVE MODEL 12340 World Trade Drive, San Diego, CA 92128 800. 854. 2235 www. carvin. com CRITICAL LISTENING POSITION 3 FT. 2-3 FT. 2-3 FT. 3 FT. 6 FT. 2 SPEAKER (stereo) AND 5. 1 (surround) SPEAKER ARRANGEMENT: The woofers should be in vertical alignment with ears, 2-3 feet away from you and the speakers should have a distance apart from one another by 3 feet. CONNECTION DIAGRAM LEFT SRS6. 5 c SRS 6. 5 STUDIO REFERENCE SERIES IMPEDANCE: 8 MAX INPUT POWER: 125 WATTS PROGRAM LEFT RIGHT 16 Gauge 2 conductor wire Serial No. RIGHT DCM1000 c SRS 6. 5 STUDIO REFERENCE SERIES IMPEDANCE: 8 MAX INPUT POWER: 125 WATTS PROGRAM MIXER or TAPE output POWER AMP Serial No. SRS6. 5A LEFT c SRS 6. 5A STUDIO REFERENCE SERIES BIAMPLIFIED CLOSE FIELD REFERENCE MONITOR 30 WATTS @ 8 OHMS (HIGH FREQUENCY) 70 WATTS @ 8 OHMS (LOW FREQUENCY) LEFT MIXER or TAPE output CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION - TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY GROUND ON THE POWER CORD - DO NOT REMOVE COVER . [. . . ] If your speaker starts this protect cycle, simply reduce your input level to the unit. If the speaker continues the protect cycle after reducing the input level, the unit is probably in thermal protect cycle. Turn the power off and wait approximately 5 minutes for it to cool down before powering up. [. . . ]