User manual CATEYE CC-CD200

[. . . ] · Never attempt to disassemble the computer head. ASTRALE8 Please keep this manual in a safe place for future reference. Important · Don't use thinner, benzene or alcohol to wipe the surface of the Note computer. CCMCD2N-030531 066600252 1 3 Mount The Bracket Secure the cord by fastening it to the frame with zip ties at regular intervals. Put the rubber pad 8 on the bracket 1 and secure the bracket on the handle bar with the screw. [. . . ] After adjusting the magnet and sensor, secure tightly with nylon ties. Left Chain Stay 3 Set The Tire Circumference Set the tire circumference in mm. Setting is fixed and completed by pushing the SET button. Increase the number Max. 2999 mm MODE 4 Marked Line 7 4 SET Decrease the number Min. 10 mm START/STOP Crank Arm 7 Center Adjust Within 5 mm Preparation Complete. (the screen will show the time measurement in this state) * The auto mode is ON in this state. Tire size is usually shown on the sidewall of tires. Computer Operations Selection of the data-display mode (bottom of the screen) Press the Mode button to navigate to each of the sub-displays listed on the right. Press and hold the mode button for two seconds in any mode to display the Clock Time. Start or Stop of Measurements Measurement Unit Icon The computer can be programmed to run in either MANUAL MODE or AUTO TIME MODE. In Manual Mode you must press the START / STOP button to turn on and off the Timer, which records Distance and Average Speeds. In Auto Time the computer turns the Timer on and off depending on a signal from the sensor. When you push the button, Elapsed Time, Average Speed and Trip Distance are recorded, and stopped with the second push of the button. · Auto Time Mode (Automatic Measurement) is lit, the measurements are automatically When the icon done. This is called auto-mode in which the rotation of the wheel is detected to make the measurements start or stop automatiis lit, you cannot start or stop the meacally. (When the icon surements by pushing the START/STOP button) · Manual Measurements on the screen, you can start or When you don't see the icon stop the measurements by pushing the START/STOP button. When you push the button, Elapsed Time, Average Speed and Trip Distance are started, and stopped with the second push of the button. START/STOP · How to set ON or OFF the Auto-Mode Tm Push the SET button while Elapsed Time (Tm) Trip Distance SET is (Dst) or Average Speed (Av) is displayed, then the icon Dst "lit" (ON) or turned OFF. Av While Elapsed Time, Trip Distance or Average Speed is displayed Display for Measurements Speed 0. 0 (4. 0) - 300. 0 km/h [0. 0 (3. 0) - 185 mph] or Power-Saving Screen (When no signal is received for about 1 hr. the screen switches to the power-saving mode) Cadence 0. 0 (20. 0) - 299. 9 rpm Auto-mode Icon When lit, the measurements starts or stops automatically. When you push either of the MODE button or the START/STOP button or you ride the bicycle, the display comes back to the measurement display. Mode Selection Illustrations (bottom of the screen) Cdc Cadence 0(20) - 299 rpm or Speed 0. 0 (4. 0) - 300. 0 km/h You can program the tire size. Odo Odometer 0. 0 - 99999 km [mile] Range of set: 10 - 2999 mm SET Mx Maximum speed 0. 0 (4. 0) - 300. 0 km/h [0. 0 (3. 0) - 180. 5 mph] When the measurements are stopped Increase the number Av MODE MODE Decrease the number Average Speed 0. 0 - 300 km/h [0. 0 - 185. 0 mph] If Elapsed Time exceeds 27 hours or Trip Distance exceeds 999. 99km, Average Speed shows E. and ceases calculation. START/STOP Resetting Elapsed Time, Trip Distance, Average and Max. Speed Push the MODE button and the START/STOP button at the same time while the measurements other than Odometer, Elapsed time, Maximum Speed, Average Speed and Trip Distance are zeroed. [. . . ] (should be within 5 mm) Speed Cadence Does the marked line of the sensor align with the center of the magnet?Additional troubleshooting at www. cateye. com Limited Warranty 2-Year Warranty : Computer Head Only (Bracket sensor and batteries are not covered under the warranty) If any trouble or damage occurs during normal use, the product computer will be repaired or replaced free of charge. Type your name, address, telephone number or e-mail address, date of purchase and the situation of trouble and send it back together with the product to the closest address below. [. . . ]