User manual CATEYE CC-CL810

[. . . ] ® CATEYE VELO5 CATEYE VELO8 CYCLOCOMPUTER Model CC-VL510/CC-VL810 ENG VELO 5 VELO 8 SET (on Back) F G U. S. CCVL51/81-070105 066600560 3 Before using the computer, please thoroughly read this manual and keep it for future reference. MODE Caution · Do not concentrate on the computer operations while riding. · Be sure to securely mount the magnet, sensor and bracket on your bicycle, and periodically check to see if any parts have loosened. [. . . ] e Power Saving Function If the main unit does not receive a signal after about 10 minutes, the main unit enters Power Saving Mode and displays the clock count only. To re turn to normal display, press the MODE button or start your bicycle again to cancel the Power Saving function. Data Reset When a screen with the Reset mark in the OPERATION FLOW is displayed, continue pressing the MODE button and the measured data will return to zero. However, the Odometer (total distance) and Clock do not return to zero. How to Set Clock In the clock mode, press SET button on the back, and the display enters clock setting mode. f How to Change Tire Size Display the Total Distance (Odo) and press the SET button to change the tire size. You can select a tire size in two ways: Either select from among preset sizes c or enter the tire's circumference directly in increments of 1 cm. d 1 3 5 2 4 3 Maintenance · If the contact of the unit or the bracket gets wet, dry it off with a cloth. · If the gaps between the buttons and the unit get clogged with mud or sand, wash them away with water. 3 Troubleshooting No display. Put the battery in backwards to short the unit then install properly and do all clear operation. (First, short-circuit the contact of the main unit a few times with a piece of metal. If current speed appears, the main unit is working fine and the cause should be attributed to the bracket or the sensor. ) Is the clearance between the sensor and the magnet too large?Are the magnet's center and the sensor's marking line aligned?Is there anything sticking on the contact of the main unit or the bracket?Wipe any water or dirt from the contacts and apply a water repellent silicon grease. Do not apply standard grease, as it may cause damage to the bracket. 4 YES! 5 5 1 NO! Replacing Battery If the screen becomes dim, it is the time to replace the battery. [. . . ] For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. (Address for service) VELO8 Reset 0. 0 - 299. 9 km/h [0. 0 - 185. 0 mph] Mx MODE Reset VELO5 0. 0 (4. 0) - 299. 9 km/h [0. 0 (3. 0) - 185. 0 mph] MODE Cal*1 Reset 0. 0 - 9999. 9 kcal Current Speed 0. 0 (4. 0) - 299. 9 km/h [0. 0 (3. 0) - 185. 0 mph] Odo 0. 0 - 9999. 9 km [mile] CO. , LTD. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn. : CATEYE Customer Service Section Clock 0:00' - 23:59' [1:00' - 12:59'] SET Service & Research Address for United States Consumers: CATEYE Service & Research Center 1705 14th St. 115 Boulder, CO 80302 Phone : 303. 443. 4595 Toll Free : 800. 5CATEYE Fax : 303. 473. 0006 E-mail : service@cateye. com URL : http://cateye. com Data Reset Reset Clock Setting Tm Dst Av Mx Cal f SET MODE (2 sec. ) 0 g a All Clear Setting Time MODE 3:10 (km/h 0 - 23) [mph 1 - 12] (00 - 59) BATTERY Close CR2032 Open MODE MODE MODE MODE MODE SET SETTING END SET [. . . ]