User manual CATEYE ENDURO 2

[. . . ] Les réparations effectuées dans le cadre de la présente garantie sont gratuites et doivent être effectuées par CAT EYE Co. , Ltd. Le produit à réparer doit être retourné à CAT EYE Co. , Ltd. Tout produit retourné au département de réparation CAT EYE doit être soigneusement emballé et le certificat de garantie ainsi que les instructions de réparation doivent accompagner le produit. Il est conseillé à l'acheteur d'écrire lisiblement ou de dactylographier ses nom et adresse sur le certificat de garantie, afin que le produit lui soit directement retourné après réparation. [. . . ] (If possible, write down the Odo data before all clear operation, and input it again after the display returns normal. ) Current speed does not appear. (When current speed does not appear, first short-circuit the contact on the back with metal; if the speed display appears, the main unit is normal and the problem must be in the bracket or the sensor. ) Is there anything on the contact of the main unit or of the bracket?Displayed with 0. 1 resolution up to 9999. 9 km and with 1. 0 resolution up to 99999 km. (With all clear operation, it returns to zero; to continue accumulation of data, input the previous Odo data after all clear operation. ) Dst(1, 2) Trip Distance(1, 2) 0. 00 - 999. 99 mile[km] ±0. 01 mile[km] Dst1 Dst2 The trip distance from start to current point is displayed. [Reset of Dst1 is always done with reset of Tm, Av and Mx all together. Reset of Dst2 is done independently of the other reset and does not affect the other data. ] Tm Elapsed Time 0:00'00" - 9:59'59" ±0. 003 % Tm moves up as Main Display Elapsed time is measured from start to current point, in units of hours, minutes and seconds. In this case, the lower display shows the hour digits of Tm data (instead of Spd). With Reset operation, it returns to zero. How to Replace Battery Insert a new lithium battery (CR2032) with the (+) pole upward. In order to continue accumulation of Odo data, write down the stored Odo before replacing the battery. Av Average Speed 0. 0 - 65 mph [105 km/h] ±0. 3 mph [km/h] Open Av moves up as Main Display The average speed from start to current point is displayed. If the elapsed time exceeds 27 hours or Dst1 exceeds 999. 99km, (. E) is displayed and calculation ceases. With reset operation, it returns to zero. Continuing Accumulation of Odo Data Although the Odo data returns to zero by all clear operation, you can continue accumulation of data by inputting the previous Odo data. Specifications Applicable Wheel Circumference --- 100cm - 300cm Applicable Fork Diameter ------------ ED200; 11ø to 40ø (Sensor Band S: 11-26ø, Sensor Band L: 21-40ø) ---------------------------------------------- MT300; 11ø to 36ø (Sensor Band S: 11-26ø, Sensor Band L: 21-36ø) Length of Wire -------------------------- 70cm Power Supply ---------------------------- Lithium Battery (CR2032) x 1 Battery Life ------------------------------- Approx. 3 years (The life of the first factory-loaded battery may be shorter than this period. ) Dimension/Weight ---------------------- 1-13/16" x 1-17/32" x 9/32" [46 x 39 x 17mm] / 0. 92 oz [26 g] * The specifications and design are subject to change without notice. Mx Maximum Speed 0. 0(3. 0) - 65 mph [105 km/h] ±1 mph [km/h] Mx moves up as Main Display Displays the highest recorded speed. With reset operation, it returns to zero. Clock time 1:00' - 12:59' or 0:00' - 23:59' ±0. 003 % If "M" is selected for speed scale, the clock time is in 12 hour. If "K", the clock time is 24 hour. CAT EYE MITY3 CC-MT300 ® E 6 5 5 1 8 7 3 0 4 9 1 Bracket 2 Wire 3 Sensor 4 Sensor Bands-A 5 Sensor Band-B 6 Magnet 7 Sensor Band Rubber Pad 8 Bracket Rubber Pad 9 Nylon Tie 0 Sensor Band Screw 2 2 3 1 1 4 Test Slide the main unit onto the bracket according to " How to Attach Main Unit to Bracket" (below). (If not, adjust the relative positions of magnet and sensor again. ) Fasten the sensor securely, and remove the main unit. 6 2 Attach the sensor temporarily. Note: Sensor Band-A (Small) --------- 11Ø-26Ø (Large) --------- 21Ø-36Ø 5 9 9 5 Secure the wire along the fork with the nylon ties 9, and wind it round the brake cable(3) up to the handlebar. Note: Allow enough wire length in the area marked with in the illustration, to insure full movement and unhindered operation of the handlebar. 3 7 4 1 (3) 1 3 3 6 (1) (2) 9 8 Test the alignment of the magnet and sensor with the main unit attached. Align the magnet's center(1) and the sensor's marking line(2). 2mm clearance between the magnet 6 and sensor 3. 3 6 (2) (1) How to Attach Main Unit to Bracket (4) 2mm Slide main unit onto the bracket from front until it clicks into position. To remove, pull it off forward while pushing down the lever(4). 1 ORIGINAL SET UP FOR THE MITY 3 AND ENDURO 2 ALL CLEAR OPERATION ST. /STOP button (S) MODE button SET button decrease the digits L cm SET UP FOR RIDING on back K (km/h)= 24hr. clock The complete screen will light up for a moment and then all fade away. Note that the speed scale you select DICTATES CLOCK function in 12 or 24 hours. [. . . ] In AUTO MODE (AT) the computer starts and stops when ever it records a signal from the sensor at the wheel. To set the computer to AUTO MODE with the computer in the DISTANCE function or TIME function, press the SET Button on the back of the computer. A small symbol with the letters AT will appear on the screen indicating AUTO MODE. You take the computer out of AUTO MODE the same way. DISTANCE, AVERAGE on back or TIME function Clock STOP STATE on back change from Hours to Minutes advance the digits Moving TIME, AVERAGE and MAX SPEED to upper display When the computer is set in AUTO MODE (AT), the functions of TIME, AVERAGE and MAX SPEED can be switched to the upper display by PRESSING the ST. / STOP (S) Button. [. . . ]