User manual CDA CI394

[. . . ] INTEGRATED WASHING MACHINE INSTRUCTIONS MANUAL EN 1 EN Contents 1. Control panel symbols 3 4 6 13 17 23 25 27 This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. [. . . ] It must absolutely remain intact and fixed to the washing machine. 12 EN 4. DESCRIPTION OF CONTROLS 4. 1 CONTROL PANEL All the commands and controls of the appliance are assembled together on the front panel. Models without delayed start option Models with delayed start option Description of controls A B C D E F G H I L M N Q R Open door button ON-OFF and programme selection knob Time remaining shown on display LED Spin speed shown on display LED Heating phase LED Display Select spin speed button Options buttons Options enabled LED's Start-Pause button Start-Pause button LED Delayed start time shown on display LED Select delayed start button Select delayed start button LED 13 EN A Open door button Press the button to open the door. Chapter 5 ­Washing instructions ­explains how the door works and how to use it. B ON-OFF and washing programme selection knob This knob lets you: switch the machine on and off by moving it in either direction from the OFF position (knob indicator vertical) select washing temperatures within the various fabric sectors by turning it in both directions The knob does not move while the programme is running. This LED indicates that the display is showing the total duration of the selected programme before the programme starts, and the time remaining while the programme is running. This LED indicates that the display is showing the maximum spin speed for the selected programme. It stays on while spin speed is being selected with the relative button. During the heating cycle, this LED indicates that the programme is in the washing water heating phase. C Time remaining shown on display LED D Spin speed shown on display LED Heating phase LED E F Display The display shows the following information: 1. The stated value is an estimate based on the machine's normal operating parameters (size of load, incoming water temperature, etc. ). The program time may therefore be a few minutes longer or shorter than stated here. When the time remaining before the programme starts is less than 60 minutes, this information is given in minutes/seconds. error codes To find out which of the first 3 pieces of information are shown on the display, check which of the LED's, C, D, or N (the latter for models featuring the delayed start option) is lit. G Select spin speed button or Press the button repeatedly to select the required spin speed. The following spin speeds are available: stop with tub full 0000: spin disabled and stop with tub full. The machine does not perform the final spin and ends the washing programme with water in the tub. To drain the water, see the explanations shown in paragraph 5. 14 from 600 rpm to the maximum speed indicated for the model: for cotton and coloured programmes, speed increases by 100 rpm starting from 600 rpm up to the maximum speed indicated for the model from 600 to 900 rpm: for synthetics, delicates and woollens programmes, speed increases by 100 rpm starting from 600 rpm up to 900 rpm. 14 EN H Options buttons Quick wash Button The options that may be available on the washing machine are shown below. This button reduces the overall duration of the washing cycle. This option is used to wash small loads or less dirty washing in less time. The bleach stage is skipped when the Quick Wash button is pressed (for models with bleach function). The machine performs a more delicate spin cycle and moves the garments at the end of the programme. Spin speed for all programmes is 600 rpm. Easy-iron button I Options enabled LED's These LED's light up when the relative option button is pressed and indicate that the option has been selected. They remain on until the machine switches off or a different selection is made. 15 EN L " Start/Pause" button Press this button to start the selected washing programme. During washing, press the " Start/Pause" button for about 3 seconds to pause the washing cycle. During the pause, the " Time remaining"Led flashes and STOP appears on the display. To resume the washing cycle from where it left off, simply press the " Start/Pause" button again. [. . . ] Put back the traps and remove any residues of detergent before putting the tray back. 6. 6 CLEANING THE WATER INLET FILTER The machine is fitted with a filter for protecting the water inlet valves. The filter is fitted the gas thread of the inlet hose connected to the tap Clean the filter if no water or insufficient quantities of water enter the washing machine. To do this, proceed as follows: Remove the plug from the socket to disconnect the machine from the electrical power supply. When screwing the inlet hose back on to the tap, make sure the filter is correctly positioned. [. . . ]