User manual CHAMBERLAIN GWUP180

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CHAMBERLAIN GWUP180. We hope that this CHAMBERLAIN GWUP180 user guide will be useful to you.


CHAMBERLAIN GWUP180 : Download the complete user guide (851 Ko)

Manual abstract: user guide CHAMBERLAIN GWUP180

Detailed instructions for use are in the User's Guide.

[. . . ] Should you need to make use of your warranty entitlement, please submit the receipt together with the item concerned. In order to avoid damage to the shutter installation during initial set up, the shutter strap must be wrapped around the strap spool at least twice when the shutter is open. The motor replaces mechanical flush mount strap coilers with strap widths from 16mm up to max. Shutter size (shutter size = length x width): Plastic-Mini- Profiles approx. [. . . ] Clean the window pane and position the light sensor onto the window pane as desired. Information: The shutter strap motor will close the shutter after 15min of direct sunlight to the position of the light sensor. In order to open/close shutter again, press corresponding button on the control panel; this may also be achieved by activated timer control. To remove or relocate the light sensor only pull on the small plug (fig. Pulling/Pushing the white plastic top may lead to destruction of light sensor. The following spare parts are available: 041AGW45 strap spool for strap lengths up to 4. Direct connection to mains supply (optional): Attention: This work should be done by a skilled worker! the shutter strap motor may be connected directly to the mains supply. Now put the phase- and neutral-wire of the mains in both of the left clamps (random order) and reinsert both of the clamp screws. Put the cable back into the strain relief and tighten screw again using a screw driver (fig. Make sure that stoppers/conical stops are existent and that these have a firm connection with the shutter. Now push any one of the three buttons of the shutter strap motor (fig. The shutter strap motor will pull the shutter up until the conical stops reach the shutter box (or wall). Then the shutter will be lowered automatically until completely closed and the lower limit is defined. Finally the shutter will be opened again automatically and will stop shortly before reaching upper limit. Should this process be interrupted through power failure or should the plug be pulled accidentally, start over again = push any one of the three buttons. The shutter can be opened or closed by pushing the Open- or Close-button ( fig. Safety function: If obstacle is hit or shutter profiles are tilted the GWUP180 will shut down automatically. Then briefly push Open-/Close-button; the shutter will move to the upper limit and the LED will glow. Then briefly push Open-/Close-button; the shutter will move to the lower limit and the LED will glow. Adjusting / Deleting / Changing additional positioning: Adjusting Keep pushing Open-/Close-button until shutter is in desired position Then push button "P" until LED stops flashing The additional position is programmed Deleting Keep pushing Open-/Close-button; the shutter will open or close completely As soon as upper/lower limit is reached shutter will stop moving Now push button "P" until LED stops flashing The additional position is deleted Changing See Adjusting Pre-programmed additional positioning will be overwritten The motor is back to its factory setting. Pushing any one of the white buttons on the control panel will lead to new initial set up / measuring of window size. [. . . ] Upon receipt of the product, the first retail purchaser is under obligation to check the product for any visible defects. Conditions: The warranty is strictly limited to the reparation or replacement of the parts of this product which are found to be defective and does not cover the costs or risks of transportation of the defective parts or product. This warranty does not cover non-defect damage caused by unreasonable use (including use not in complete accordance with Chamberlain's instructions for installation, operation and care; failure to provide necessary maintenance and adjustment; or any adaptations of or alterations to the products), labor charges for dismantling or reinstalling of a repaired or replaced unit or replacement batteries. A product under warranty which is determined to be defective in materials and/or workmanship will be repaired or replaced (at Chamberlain's option) at no cost to the owner for the repair and/or replacement parts and/or product. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CHAMBERLAIN GWUP180




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CHAMBERLAIN GWUP180 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.