User manual CHAMBERLAIN HC624ML

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CHAMBERLAIN HC624ML. We hope that this CHAMBERLAIN HC624ML user guide will be useful to you.


CHAMBERLAIN HC624ML : Download the complete user guide (11564 Ko)

You may also download the following manuals related to this product:

   CHAMBERLAIN HC624ML (8717 ko)
   CHAMBERLAIN HC624ML (8717 ko)
   CHAMBERLAIN HC624ML (8717 ko)

Manual abstract: user guide CHAMBERLAIN HC624ML

Detailed instructions for use are in the User's Guide.

[. . . ] Automatic Gate Opener Models , when installed and maintained according to all the Manufacturer's instructions in combination with a Gate, which has also been installed and maintained according to all the Manufacturer's instructions, meets the provisions of EU Directive 98/38/EC and all amendments. I, the undersigned, hereby declare that the equipment specified above and any accessory listed in the manual conforms to the above Directives and Standards. This safety alert symbol means "Caution" - failure to comply with such an instruction involves risk of personal injury or damage to property. This gate drive mechanism is designed and tested to offer appropriately safe service provided it is installed and operated in strict accordance with the following safety rules. [. . . ] The drive must be standing on a solid surface for the purposes of breaking the holes through to prevent the PVC base plate from breaking. A small, flat screwdriver should be used for breaking the holes through. For this purpose, tap on the screwdriver handle with the palm of the hand from the inside. The pre-punched area can then be easily removed and the strain relief supplied as standard fitted in its place. There is a small switch operated by a cam under the operator's cover. Switch free switch fully pushed (cam operates switch) switch free Use the socket spanner supplied in the hardware bag to lift the cover up. The release key located beneath the hood should be inserted into the side openings and turned approx. To reengage it, the key should be turned back to its original position. The door leaf can move in an uncontrolled way, especially if it is defective and not properly balanced. Before initial operation check if operator does not come in contact with the gate in the fully OPEN position. One of these guidelines specifies that the closing forces at the gate edge must not exceed 400 N (40 kg) for the last 500 mm before the door is CLOSED. Above 500 mm, the maximum force at the gate edge must not exceed 1400 N (140 kg). If this cannot be ensured, a contact strip must be mounted on the gate at a height up to 2. Note: The listed accessories on page 2 are especially suited for the professional installation of a gate system. The control consists of several components which are fitted together and are screwed into the box. Find the following parts in the control box: - Remote control - Exterior installation box - Cover for box - Control - Transformer - Baseplate for transformer - Radio receiver - Radio module - Cable bushing large - Cable bushing small - Flat washer - Screws 3, 5x 9, 5 mm 1-2x* 1 1 1 1 1 1 1 1 1 5 17 Open the 4 pre-cut holes at the bottom of the casing with a screwdriver or a similar device. Attach large cable bushing on the left then the rest as shown in picture. All openings and cable bushings must be sealed against water (waterproof). The control box with the motor control is to be mounted with the cable bushings facing down. Fasten control box of casing to wall, after previously measuring required distances and establishing correct position of drill-holes. On the right hand side of transformer there is sufficient space for a second transformer( Screws 3. Attach short earthing cable (yellow/green) to the plate using a screw and a washer. [. . . ] Operate the gate with a remote control or with a connected switch and monitor the direction. If all adjustments are done, check operation of photocells, switch, flashing light, remotes, accessories, etc. Advise people using the gate with regard to gate operation, safety functions and how to release the gate in order to operate it manually. tIMER TO CLOSE NOTE: Only possible with connected photocells (1 + COM). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CHAMBERLAIN HC624ML




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CHAMBERLAIN HC624ML will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.