User manual CHAMBERLAIN NLS1

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CHAMBERLAIN NLS1. We hope that this CHAMBERLAIN NLS1 user guide will be useful to you.


CHAMBERLAIN NLS1 : Download the complete user guide (412 Ko)

Manual abstract: user guide CHAMBERLAIN NLS1

Detailed instructions for use are in the User's Guide.

[. . . ] The default channel for the intercom is the paging channel where all four channel lights are lit. An intercom on a channel can only hear an intercom on the same channel or on the paging channel. HOLD OFF ACTIV VOLU ME E TALK MONIT OR 1 3 CHAN 2 NEL 4 Carton Inventory HOLD OFF VOLUME MONITOR ACTIVE TALK 1 2 3 4 CHANNEL (2 in Model NLS2) Intercom (2 in Model NLS2) OPTIONAL Operation & Features Channel Lights Talk Button Active Light Speaker Channel Select Button Conference Mode: Conference Mode allows multiple intercoms to participate in a conversation compared to Normal Mode in which only two intercoms can communicate. All intercoms must be set to the same channel or the paging channel to be 1 2 in Conference Mode. [. . . ] When batteries are low intercom will emit three beeps every ten minutes. In this case, the channel lights will remain on. VE ACTI TALK 1 3 2 4 Assemble Intercom Step 1 INTERCOM HOLD OFF VOLUME MONITOR ACTIVE OR CHANNEL 4 LEARN MODE Press the Learn button until a beep is heard. TALK 1 2 3 Each intercom will emit a tone when entering programming mode. It may take up to 3-1/2 minutes for a secure network to be established. Add to an Existing Network Step 2 Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put any networked intercom into Learn Mode (refer to table below). INTERCOM HOLD OFF VOLUME MONITOR ACTIVE OR CHANNEL 4 TALK 1 2 3 Adhere rubber pads to bottom. Repeat Steps 1 and 2 for any additional intercoms. Each intercom will emit a tone when entering programming mode. It may take up to 3-1/2 minutes for a secure network to be established. NOTE: Do not program new intercoms to each other before adding them to the network or they will form a separate network and the memory will need to be cleared. Programming Intercom The intercom must be programmed to at least one other intercom to become a network or it can be programmed into an existing network. Create New Network HOLD OFF Before programming, clear memory on all intercoms. Within 10 seconds put the second intercom into Learn Mode (refer to the following table). 2 Press and release the Talk button to verify network is complete. HOLDF OF ME VOLU OR MONIT Install 4 AA Alkaline batteries (not provided). VE ACTI TALK 1 3 2 4 HOLDF OF VE ACTI LEARN MODE Press the Learn button until a beep is heard. ACTIV VOLU ME E ME VOLU TALK 1 OR MONIT 3 2 4 TALK MONI TOR 1 2 3 4 CHAN NEL Troubleshooting Intercom does not function. Cell phones, cordless phones, or other radio devices may also limit range. Replace with AA Alkaline batteries or operate it with DC Adapter (not provided). A 12 volt, 300mA DC Adapter may be used (center positive polarity on the round plug). A cordless phone, cell phone, or other radio devices can also cause static. The intercom does not connect to another intercom and a green light is on longer than 3-1/2 minutes. Place the intercom closer to the other intercoms in the network, with the antenna pointing up. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CHAMBERLAIN NLS1




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CHAMBERLAIN NLS1 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.