User manual CHAMBERLAIN RA15
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CHAMBERLAIN RA15. We hope that this CHAMBERLAIN RA15 user guide will be useful to you.
Manual abstract: user guide CHAMBERLAIN RA15
Detailed instructions for use are in the User's Guide.
[. . . ] Neither the manufacturer nor the supplier assumes any liability for personal injury, damage to property or consequential injury or damage occurring as a result of the use of non-approved third party products or changes made to any accessories. Prior to performing installation work, de-activate all connections and control facilities that are not absolutely essential for operation of the given system. Fit control facilities within sight of the product to be controlled at a height of at least 1. Ensure sufficient room is left between any moving parts and nearby objects. [. . . ] Proceed according to the specific requirements for left-sided (a) or right-sided (b) operation: Secure the mounting bracket (7) to the wall (use suitable screws and plugs). The illustration H also shows the wall bracket on the drive side (b), the motor (a); the steel tube (c); the end cap (d); and the opposite wall bearing (e). Never connect more than one motor to a timer or wall switch without using a central module (h) (available as an accessory), i. For a left-side motor installation, follow the wiring diagram exactly as shown in the control accessory package. For the correct direction of rotation in a right-side motor installation, electrical wires (brown & black) must be reversed between the control accessory and the motor. Have the electrical hook-up done by a qualified electrician in compliance with your local electrical code. "Open" and "Close" Positions In general the following applies: + #1 #2 = Stops later = Stops earlier White screw Red screw Advice: In order to fix the roller shutter hangers to the shaft, ONLY use short fixing screws. The recommended fixing method for the hangers is without screws by means of spring band loops (which are hooked on). I look into the box and the limit switch of the motor is on the left (see Fig. l1) White = Limit switch AT BOTTOM Red = Limit switch AT TOP B: A right-handed installation. I look into the box and the limit switch of the motor is on the right (see Fig. L2) Red = Limit switch AT BOTTOM White = Limit switch AT TOP The bottom adjusting screw is always for the upper limit and the upper is always for the lower limit, no matter whether the motor is pushed into the shaft from the right or the left. Run the roller shutter drive downwards until it switches itself off and then (and only then) attach the roller shutter jacket to the shaft. Advice: In order to fix the roller shutter hangers to the shaft, ONLY use short fixing screws. The recommended fixing method for the hangers is without screws by means of spring band loops (which are hooked on). If it switches off too early the bottom adjusting screw must be adjusted in the plus direction. Each full turn of this screw extends the travel path by about 40° of one turn of the motor. After this the drive must be driven back a little and then up again to check the result. It is possible that the drive will switch itself off after several trips because it has reached a temperature which is too high. Howevere after 15 20 minutes cooling time it will be ready to operate again. Please note that the limit switches of the drive only function properly if the drive has been installed correctly and is completely within the shaft. 1 yellow-green 2 blue 3 black 4 brown The limit switches have already been adjusted and both limit switches turned to the minimum. [. . . ] Upon receipt of the product, the first retail purchaser is under obligation to check the product for any visible defects. Conditions: The warranty is strictly limited to the reparation or replacement of the parts of this product which are found to be defective and does not cover the costs or risks of transportation of the defective parts or products. This warranty does not cover non-defect damage caused by unreasonable use (including use not in complete accordance with Chamberlain's instructions for installation, operation and care; failure to provide necessary maintenance and adjustment; or any adaptations of or alterations to the products), labor charges for dismantling or reinstalling of a repaired or replaced unit or replacement batteries. A product under warranty which is determined to be defective in materials and/or workmanship will be repaired or replaced (at Chamberlain's option) at no cost to the owner for the repair and/or replacement parts and/or product. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CHAMBERLAIN RA15
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CHAMBERLAIN RA15 will begin.