User manual CHAMBERLAIN RPD25F

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CHAMBERLAIN RPD25F. We hope that this CHAMBERLAIN RPD25F user guide will be useful to you.


CHAMBERLAIN RPD25F : Download the complete user guide (2779 Ko)

Manual abstract: user guide CHAMBERLAIN RPD25F

Detailed instructions for use are in the User's Guide.

[. . . ] all the standards and regulations applying to electrical installations must be observed. Only those spare parts, tools and other equipment as have been approved by Chamberlain may be used. Neither the manufacturer nor the supplier assumes any liability for personal injury, damage to property or consequential injury or damage occurring as a result of the use of non-approved third party products or changes made to any accessories. Prior to performing installation work, de-activate all connections and control facilities that are not absolutely essential for operation of the given system. [. . . ] It is possible that the drive will switch itself off after several trips because it has reached a temperature which is too high. Howevere after 15 ­ 20 minutes cooling time it will be ready to operate again. Please note that the limit switches of the drive only function properly if the drive has been installed correctly and is completely within the shaft. Advice: In order to fix the roller shutter hangers to the shaft, ONLY use short fixing screws. The recommended fixing method for the hangers is without screws by means of spring band loops (which are hooked on). The middle button stops the shutter in any position as required (stop). If, during an upward or downward movement, the button for the reverse direction is pressed, the motor automatically changes the direction of travel. The drive should turn 2x briefly and then run to one of the limit switches as a signal that the command has been understood. Disconnect link to black cable making sure the free end cannot cause a short circuit. For further steps, see "Programming the first remote control". Make sure no electric cables are damaged when fitting the bracket, particularly when installation is to occur near light switches or power sockets. pROGRAMMING RADIO REMOTE CONTROLS (HAND-HELD TRANSMITTERS) Up to 40x remote controls can be memorised. The first remote control programmed is also called the "master" remote control. PROGRAMMING A NEW, ADDITIONAL REMOTE CONTROL (not the first one or so-called master) PLEASE NOTE: The following steps must be executed quickly. The easiest way is for a second person to help by reading out the text while the other person presses the buttons. via the master remote control: Step 2: Press and hold the STOP button. The drive turns 2x briefly as a signal indicating that the command has been understood (approx. Step 3: Then press the UP button (upper button) and also the DOWN button (lower button) immediately and briefly. Once again the drive moves 2x briefly as a signal that the command has been understood. Via the new remote control: Step 4: Press and hold the UP button (upper button) on the new remote control immediately. Once again the drive moves 2x briefly as a signal that the command has been understood. Note 3: Don't press a new button before the LED on the remote control has gone out and the drive has stopped moving. [. . . ] Upon receipt of the product, the first retail purchaser is under obligation to check the product for any visible defects. Conditions: The warranty is strictly limited to the reparation or replacement of the parts of this product which are found to be defective and does not cover the costs or risks of transportation of the defective parts or products. This warranty does not cover non-defect damage caused by unreasonable use (including use not in complete accordance with Chamberlain's instructions for installation, operation and care; failure to provide necessary maintenance and adjustment; or any adaptations of or alterations to the products), labor charges for dismantling or reinstalling of a repaired or replaced unit or replacement batteries. A product under warranty which is determined to be defective in materials and/or workmanship will be repaired or replaced (at Chamberlain's option) at no cost to the owner for the repair and/or replacement parts and/or product. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CHAMBERLAIN RPD25F




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CHAMBERLAIN RPD25F will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.