Detailed instructions for use are in the User's Guide.
[. . . ] GL
CO NT RO LL ER
BO AR D
HEAVY DUTY SLIDE GATE OPERATOR
2 YEAR WARRANTY
Serial # ________________________ (located on electrical box cover) Installation Date__________________ MODEL SL575 IS FOR VEHICULAR PASSAGE GATES ONLY AND IS NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE
MODEL SL575
TABLE OF CONTENTS
OPERATOR SPECIFICATIONS
Carton Inventory . 4 · These instructions are intended to highlight certain safety related issues. Because each application is unique, it is the responsibility of the purchaser, designer, installer and end user to ensure that the total gate system is safe for its intended use.
OPERATOR WARNINGS
Safety Installation Information . . 7
WARNING
Mechanical
WIRING
WARNING Power Wiring Installation . [. . . ] Accessories that may be wired to this input include: Telephone Entry Systems, Radio Receiver (Commercial Applications), Exit Loop Detector, Keypads, 7-Day Timer. NOTE: Will not override a double entrapment (signalled by the gate stopped and entrapment alarm on).
REMOTELY MOUNTED STOP/RESET CONTROL WIRING · This control will function as a Stop/Reset command and is to be wired within line of sight of the gate. · Wire Stop/Reset control station to terminals 3 and 5 on the control box on the operator. Make sure that all Stop/Reset controls are wired in series.
123 56 789 0#
Soft Open
1 234567
Control Conduit Control Conduit
1
2
3
Stop/Reset Button
Stop/Reset Button
19
M
ACCESSORY WIRING (CONTINUED)
Terminals 7 & 5 (Com) - Hard Open Override Control Input These terminals are intended for use only with the open control of a 3-button station that is installed within line of sight of the gate. Activation of this input for longer than three seconds will enable the control to be used as a constant pressure override device. This will allow the user, in emergencies, to override a failed accessory such as a loop detector or photo-eye. Terminals 4 & 5 (Com) - Close Override Control Input These terminals are intended for use only with the close control of a 3-button station that is installed within line of sight of the gate. Activation of this input for longer than three seconds will enable the control to be used as a constant pressure override device. This will allow the user, in emergencies, to override a failed accessory such as a loop detector or photo-eye. Terminals 8 & 5 (Com) - Interrupt (Safety) Loop Input These terminals are intended for use with a loop detector. Terminals 2 & 5 (Com) - Shadow Loop Input These terminals are intended for use with a loop detector and is primarily used on swing gate operators. This input protects cars by preventing the gate from moving off of the open or close limit when the shadow loop input is active. Commands are seen when +24Vdc is applied to the controller's input terminals. NOTE: The control board has built in surge suppression circuitry however please take precautions when adding any additional surge protection. MASTER/SECOND SYSTEMS Dual Gate Communications The control board is capable of running the operator in a master or second mode depending on (S4) switch setting. Before initiating any command the master unit queries for the presence of a "second unit" for a time period of one second. If the master gets no response the operator will operate in a stand alone mode. NOTE: For single unit applications, a jumper must be placed between 11 and 12 of the field wiring terminal block. If the master detects the presence of a second unit the master will continue to query the second unit during travel. The second operator will stop if there is a period of one second or more of no communications. When two operators are connected in dual gate configuration accessories may be connected to either the master or second. NOTE: Do not run Master/Second communication wiring in the same conduit as the power and control wiring. [. . . ] Idler shaft kit Complete with: Bearings, sprocket 50B12x1" and idler shaft Cover kit Complete with: Cover and lock bar Alarm kit Complete with: Alarm and cable Disconnect kit Output shaft kit Complete with: Output shaft, sprockets, e-ring, washer, key, set screw, roll pin and spacer. Clutch shaft kit Complete with: Clutch shaft, sprockets, e-ring, compression spring, pulley, washer, bearings, retaining ring, disconnect splined hub and roll pin. NOT SHOWN Roller Chain (Sprocket Reduction) Antenna
K2
K75-34824
K3
K75-34828
K4 K5 K6 K7
K75-34842 K29-32410 K75-19977 K72-34844
10
23-3001 23-3005
K8
K72-34845
01-34851 01-34851SP 01-34851FR
19-48047M K1C3196-3
34
ILLUSTRATED PARTS
5
9 8
K4 (K75-34842)
3
7
K6 (K75-19977)
10 4
K7 (K72-34844)
K3 (K75-34828)
K2 (K75-34824)
K8 (K72-34845)
K5 (K29-32410)
1
2
6
K1 (71-B120) (71-B240) (71-B575) K3 (K75-34828)
35
ELECTRICAL BOX
5 3 4 7
1 3 9
2
K1 (K72-34818)
6 8
INDIVIDUAL PARTS ITEM 1 2 3 4 5 6 7 PART # K001A5566 312HM 13-10024 23-10041 03-8024-K 23-34822 21-3260-1 21-10298-1 23-30716 25-2006 25-2008 DESCRIPTION Control board Radio - 315 MHz Limit nut Limit switch Contactor Open/close switch Transformer -115/208/230/460Vac/60VA Transformer - 575Vac/100VA Stop switch VARIABLE PARTS Overload - 6 AMP - SL575-50-21, SL575-50-81 Overload - 8 AMP - SL575-75-21, SL575-75-81, SL575-100-21, SL575-100-81 Overload - 10 AMP - SL575-50-11 Overload - 15 AMP - SL575-100-11 Overload - 1. 8 to 2. 6 AMP SL575-100-53 (NOT SHOWN) RPM Sensor (Hall effect) 36 ITEM K1 PART # K72-34818
SERVICE KITS DESCRIPTION Limit shaft kit Complete with: Limit shaft, limit nuts, limit bearings, limit sprocket, shim washers, compression ring, roll pin and e-ring.
*To order a complete replacement electrical box kit contact technical support at 1-800-528-2806.
8 9
25-2010 25-2015 25-4002-SK
K74-18379
*Non stocked item. Please allow additional delivery time.
NOTES
37
NOTES
38
NOTES
39
WARRANTY POLICY AND SERVICE
LIFTMASTER® TWO YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. [. . . ]