User manual CHEVROLET IMPALA POLICE 2011

[. . . ] i-1 ii Introduction The information in this manual supplements the owner manual. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual. Please refer to the purchase documentation relating to your specific vehicle to confirm each of the features found on your vehicle. For vehicles first sold in Canada, substitute the name "General Motors of Canada Limited" for Chevrolet Motor Division wherever it appears in this manual. [. . . ] Consult the appropriate service manual for more trim height information. 11-2 Technical Data Capacities and Specifications The following approximate capacities are given in metric and English conversions. Application Capacities Metric English For the air conditioning system refrigerant charge amount, see the refrigerant label located under the hood. 10. 0L 4. 8L 7. 5L 10. 6 qts 5. 1 qts 7. 9 qts Air Conditioning Refrigerant Cooling System Engine Oil with Filter Transmission Fluid (Bottom Pan Removal) All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual. Special Equipment Options 15-1 15-15 Special Equipment Options SEO Standard Options SEO Standard Options - Police Package and Special Service Package . 15-10 SEO Available Options SEO Available Options - Police Package and Special Service Package . Wiring Provisions for Vehicle Grille Lamps, Flasher and Speaker/ Siren - SEO 6J3 . . 15-16 15-18 15-18 15-18 15-19 15-19 15-21 15-23 15-26 15-2 Special Equipment Options . SEO Standard Options SEO Standard Options - Police Package and Special Service Package Notice: GM cannot be responsible for any changes made to the vehicle. Have all electrical and body modifications performed by experienced technicians. . Do not route wiring in areas of the vehicle where temperatures can be high or where wiring may be cut, pinched, or rubbed. See that all added wiring is of the same or larger gauge than the wire it is being attached to for proper fuse protection. Be sure that all holes drilled in the body are properly sealed and corrosion protected. See that the vehicle's wiring harnesses, piping, and other components have not been displaced or damaged during customer installations of equipment and wiring. Do not route wiring or equipment which could interfere with roofmounted side impact airbags. Do not overload the vehicle's system by having unnecessary accessories on at the same time. . Power Steering/Engine Oil Cooling System . Be sure that any modified or added wiring will work properly with your vehicle's wiring system. See that all wiring is properly protected by fuses, and not causing an overload to connectors and components. . A. Engine Oil Cooler . B. Transmission Fluid Cooler Your Impala police vehicle is equipped with auxiliary fin-type air-to-oil coolers mounted in front of the engine coolant radiator. Notice: Overloading the vehicle's electrical system may damage your vehicle's accessories. Special Equipment Options The engine oil and power steering fluid coolers are mounted on a common frame to the right of center. The transmission fluid cooler is mounted separately to the left of center and provides fluid cooling in addition to the coolant radiator end-tank cooling. 15-3 Trunk Ground Stud A 10 mm flanged hex nut grounds the 10 mm bolt to the vehicle. Recommended torque for the flanged nut is 35 N·m (26 lb ft), plus or minus 5 N·m (4 lb ft). Recommended torque for the terminal connection nut is 10 N·m (7. 3 lb ft), plus or minus 1. 3 N·m (1 lb ft). A 10 mm ground stud can be found in the trunk on the passenger side of the vehicle. See "Trunk Auxiliary Battery Power Junction Block" that follows for more information on location. 15-4 Special Equipment Options Wiring Provisions for 12-Volt Battery Power Supply Special Equipment Options 15-5 15-6 Special Equipment Options Two 30 amp circuit breakers supply power from the 65 amp fusible link through the contacts of the control relays to 3. 0 mm² (12 gauge) blunt cut wires. The blunt cut leads are part of a 1. 5 m (5 ft) loop of wire coiled under the instrument panel in the front passenger side footwell. Each relay is operated by an 0. 8 mm² (18 gauge) blunt cut, light or dark blue control lead included in the 1. 5 m (5 ft) coil under the instrument panel. An 8. 0 mm² (8 gauge) ground lead is also provided in the 1. 5 m (5 ft) coil. The total current available through the 12-volt power supply is 110 amps (1320 watts). [. . . ] 6J5 Hole Location 15-22 Special Equipment Options Wiring Diagram for SEO 6F5 Special Equipment Options Option 6F5 is a universal wiring harness for roof-mounted equipment. The harness is routed from a 1. 5 m (5 ft) coil of wire in the passenger side footwell to a connector on the passenger side of the trunk. When the SEO 6B7 (center hole) is ordered, two color-coded 5. 0 mm² (10 gauge) wires extend 60 cm (24 in) through a grommet approximately 74 cm (30 in) behind the top of the windshield at the center of the roof. When SEO 6J5 (passenger side hole) is ordered, two colorcoded 5. 0 mm² (10gauge) wires extend 60 cm (24 in) through a grommet approximately 74 cm (30 in) behind the top of the windshield and 15 cm (6 in) inboard from the passenger side longitudinal roof joint. [. . . ]