User manual CISSELL AUCMAN150140

[. . . ] 7 menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 8 program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] G. Act (Guard actiontime - default 5) On the lower display appears the time that the drum has to be activated during the anti-crease time. If necessary, change this program with the upper or lower button (5 to 240 seconds) and confirm afterwards with the middle button. When in the setting menu at "rEVE", "YES" was programmed, this action time will be executed left and right alternately End The programming of the variable manual program has ended here. Select by means of the upper button no to program another program and confirm with the middle button. 17 2 18 2 Programming of the fixed programs The drying time of these programs can be built up in different subdivisions (max. This way, it is possible to for example in the beginning of a drying time work with a higher temperature - in order to achieve a quicker drying - while to the end, this temperature - to avoid shrinking of the linen - will be decreased. These programs can be built up manual, automatic or in combination of these two drying systems. Remark When no residual moisture measuring system is used, only manual drying system is possible. Drying time Example : Drying program 50 ° : Part 1 Part 2 Part 3 Cooldowntime Anti-crease 55° stop: 5 act: 60 15' 50° stop: 5 act: 60 5' 45° stop: 5 act: 30 drY1 45° stop: 5 act: 30 3' 30' stop: 120 act: 5 1-30 On the lower display a program number is mentioned. If a "- sign" appears before the number, this means that this program number does not contain a program, and you go immediately to "FL. tE". Now by pressing the upper button, you can possibly select out of "CoPY" or "dEL". So, the program can be used as basis and this can save a lot of programming time (see further copying a program) dEL: To delete a program (see further deleting a program). FL. tE (flash temperature - default 5) On the upper display appears how many seconds the temperature indication has to be mentioned during the drying cycle. The combination of the parameters FL. tE and FL. FU (see further) will result in an alternate indication of the residual drying time or residual moisture and the temperature. Change this setting when necessary by means of the top or bottom button (5 to 600 seconds) and then confirm by means of the middle button. This parameter is not shown when "0" was selected with "Cy. on". turn By means of the upper button you have to select the direction of rotation of the drum righ: right (clockwise) left: left (anticlockwise) Confirm the program afterwards with the middle button and you go to "CY. on" or " XX-1". 21 2 22 CY. rE (Cycle repeat)(default : 1) The bottom display shows how many times the contact needs to close and open. Change this setting when necessary by means of the top or bottom button (1 to 99 pulses) and then confirm by means of the middle button. CY. St (Cycle start) The bottom display shows how the pulsating function of the cycle contact will start. OFF : the cycle contact will first remain open during the time chosen with (CY. of). On : the cycle contact will first remain closed during the time chosen with (CY. on) Change this setting when necessary by means of the top or bottom button (on-off pulses) and then confirm by means of the middle button. By pressing the middle button, earlier adjusted programs can be controlled or changed. By pressing the upper button, you will go to the next subdivision of the drying cycle. Therefore, select "tiME" or "PERC" with the upper button and confirm afterwards with the middle button (transition to "tEMP"). Therefore select with the upper button "donE" and confirm afterwards with the middle button. [. . . ] During the cool down time, the lower display shows alternately the cool down temperature and the residual cool down time. End of cool down time : transition to anti-crease time When the cool down time is over, or when the cool down temperature is reached, the anti-crease time starts automatically. On the lower display, the programmed anti-crease time is counted per second. End of the drying program When the anti-crease time is over, the program stops automatically and "End" appears on the lower display. Manual interfering Opening of the door or filterdoor during the program When during a program the door is opened, everything stops and on the upper display, "door" and "Lint" appears alternately. The residual drying and cool down time is still counting on the lower display. When during a drying or cool down time the door is closed again, "Push" is mentioned alternately with the program number (or "CooL"). [. . . ]