User manual CISSELL CSHW35-HW55-164

[. . . ] Contents 1 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Technical data and dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If F5 is activated during final spin, this segment of the program will be skipped as described above. It is however followed by a coast and tumble time to disentangle the linen. This special function prevents the user from opening the machine while the drum is still rotating and represents an important safety feature. To return to normal operation, press the START-button (S). Attention! Function F6 (no spin): This function eliminates all spin action. During final spin, only the programmed low spin time will be completed as regular wash action. This function influences the cycle time - the program continues normally - and remains active until the START-button (S) is pressed. Function F7 (indication of the rpm) By using F7 the number of revolutions of the drum (rpm) appears on the right display. Function F8 ( changing the number of revolutions (rpm) at final spin) By means of F8, the number of revolutions can be changed at high spin. Each time you press the ECO button (E), the spin decreases with 25 rpm ( min. 500). Each time you press the START button (S), the spin increases with 25 rpm (max. 999). Remark : This function has to be selected before final spin has started. 19 4 End of a program At the end of a program, while the door is being released, the left display shows End; and the Start-LED is switched off. After that only the right display will continue to show the program number. This is the end of the program. Premature ending of the program By pressing the START-button (S) during the program, the Start-LED is switched off and the water is drained from the machine. As long as the water has not reached the safety level, the door will remain sealed and the display will show SLE (Safety Level) on the left display. Afterwards the display will temporarily show End on the same display and the Start-LED will be switched off. After that only the right display will continue to show the program number. This is the end of the program. Remark: If any attempt is made to interrupt the program prematurely during a spin phase of the program, all functions on the display will be temperary replaced by blinking horizontal dashes. After that only the right display will continue to show the program number and the door will be released. This is the end of the program. 20 4 Remarks: Freely programmable stop-function Before starting a program it is possible to preprogram a time stop in every program segment. This function permits special additional functions like adding bleach or extra detergent to the wash bath. Programming: After selecting the program, press the ECO-button (E) and keep it depressed. The left display now shows StO (Stop) and the right display shows the program number. [. . . ] These have been designed in cooperation with specialized detergent manufacturers to obtain the best possible wash results using the most frequently used detergents. Program 0 (starching) is mostly used in very special applications and is therefore not displayed on the front panel. 0. CURTAINS 1 RINSE 2 BATHS 1 BATH 2 BATHS 1 BATH 2 BATHS 1 BATH 2 BATHS 1 BATH 1 BATH COLD 40°/90°C 90°C 40°/60° 60°C 40°/40°C 40°C 30°/30°C 30° COLD 29 6 Technical remarks Internal connections of the electrical heating 1 AC Heating 3kw R5 LC1D0901 3 AC s Heating 4, 2kw 3x1, 4kw 6kw 9kw 12kw 12kw 3x2kw 3x3kw 3x4kw 3x2kw 3x2kw 3x2kw 3x3kw 3x3kw 3x3kw 3x3kw 3x4kw 3x4kw 3x4kw 3x230V s s s -----s R5 LC1D0901 LC1D0901 LC1D1810 -----LC1D253 3x400V H H H s H R5 LC1D0901 LC1D0901 LC1D0901 LC1D0901 LC1D0901 H 15kw 18kw s LC1D253 H LC1D1810 s LC1D323 H LC1D1810 21kw --------------------- --------------------- H s s s LC1D1810 LC1D1810 LC1D1810 LC1D1810 24kw B = Black Gy = Grey R = Red PU = Purple Br = Brown Bu = Blue W = White W/B = White/black Remark: Other executions are available as options. Tilt switch 1/2 1/2 Window The tilt switch is mounted on the solid part of the machine. There is a window around the probe of the tilt switch that is mounted on the movable part of the machine. [. . . ]