User manual CISSELL MANHD175LB

[. . . ] HD LAUNDRY DRYER Gas: Natural and LP Steam HD175 MAN 175lb 3/06 Cissell Manufacturing Co. 831 S. - 40232-2270 Tel: (502) 587-1292 - Fax: (502) 585-2333 Sales Fax: (502) 585-3625 - Service/Parts Fax: (502) 681-1275 THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER Page 1 IMPORTANT NOTICES--PLEASE READ For optimum efficiency and safety, we recommend that you read the manual before operating the equipment. WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life. - Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. [. . . ] NEVER exhaust into a wall, ceiling, or concealed space. 1. Make-up air opening from outside the building may enter the enclosure from the top or side walls. The area of the opening should be equal to 4 to 6 times the sum of the dryer duct areas. Provide 1 square foot for each 6 inches diameter; 2 square feet for each 8 inches diameter; and 4 square feet for each 12 inches diameter. If dryers use room air instead of outside air, additional heat loss can be another 25 Btu/h for each cubic foot per minute (cfm) used. Heat loss into laundry room from dryer front panels is about 60 Btu/h per square foot. 2. 3. Page 27 Exhaust and Venting DRYER AIR FLOW INSTALLATION Nothing is more important than air flow for the proper operation of a clothes dryer. A dryer is a pump which draws make-up air from the out-ofdoors, through the heater, through the clothes and then forces the air through the exhaust duct back to the out-of-doors. Just as in a fluid water pump, there must be the proper fluid air flow out of the exhaust duct. In summary, there must be the proper size out-of-doors inlet air opening (46 times the combined areas of the air outlet) and an exhaust duct, size and length of which allows flow through the dryer with no more than 0. 6 inches water column static pressure in the exhaust duct. In some instances, special fans are required to supply make-up air, and/or boost exhaust fans are required for both regular and energy savings models. FOR BEST DRYING FOR BEST DRYING: 1. Exhaust duct maximum length 14 feet of straight duct and maximum to two 90º bends. Use clean-outs in the exhaust duct and clean periodically when needed. Never exceed 0. 6 inches water column static pressure in the exhaust duct. Provide opening to the out-of-doors in accordance with the following: For each dryer 8 inches diameter exhaust requires 2 square feet make-up air. Use barometric shutters in the inlet air opening to control air when dryers are not running. FOR BEST DRYING OTHER RECOMMENDATIONS TROUBLESHOOTING OTHER RECOMMENDATIONS To assure compliance, consult local building code requirements. TROUBLESHOOTING Hot dryer surfaces, scorched clothes, slow drying, lint accumulations, or air switch malfunction are indicators of exhaust duct and/or make-up air problems. Page 28 Rules for Safe Operation of Your Dryer RULES FOR SAFE OPERATION OF YOUR DRYER RULES 1. Be sure your dryer is installed properly in accordance with the recommended instructions. CAUTION Be safe - Shut main electrical power supply and gas supply off externally before attempting service. Never use dry cleaning solvents: gasoline, kerosene, or other flammible liquids in the dryer. Always keep the lint screen clean; a full lint screen may be a fire hazard. Never use heat to dry items that contain plastic, foam, or sponge rubber, or rags coated with wax or paint. Serious injury will occur if a child should crawl inside and the dryer is turned on. Never use the dryer door opening and top (or the lint drawer) as a step stool. Read and follow manufacturer's instructions on packages of laundry and cleaning aids. [. . . ] 1/4" LOCKWASHER 1/4" FLATWASHER ORFICE 12 13 14 15 16 17 18 19 20 21 22 TU4600 TU4602 TU4605 TU4608 TU4934 TU7733 TUX352 TU14796 TU14797 TUX391 TU10946 3/4" UNION 3/4"-90 STREET ELL. NUT #8-18 x 1/2" SCREW 3/4" GAS VALVE GAS BURNER IGNITION BURNER 1-1/4 x 3" NIPPLE MANIFOLD PLUG Page 63 TU14398 - 24V STEAM BONNET ASSEMBLY 1 2 3 4 5 6 7 8 CB36 TU13517 TU14397 TU1699 TU2846 TU2847 TU4597 TU4599 SCREW, 1/4-20 x 1/2 VALVE, 3/4 STEAM ASM, BON. WELD COIL, 6 x 10 STEAM WASHER, 1/4 LOCK WASHER, 1/4 FLAT TEE, 3/4 STD. IRON NIPPLE, 3/4 x 18" LG. 9 10 11 12 13 14 15 16 TU4600 TU4605 TU4608 TU4610 TU4620 TU9889 TU9890 TU9953 UNION, 3/4 ELL, 3/4 90 DEG. [. . . ]