User manual CISSELL NEW UTILITY

[. . . ] For warranty service, contact the Distributor from whom the Cissell equipment or part was purchased. If the Distributor cannot be reached, contact Cissell. Page 2 TABLE OF CONTENTS MU42 and MU45 (UTILITY) PAGE Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Foreward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Lower Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Head Release Assembly (Lower Pivot). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Head Release Unit (Upper Pivot). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pivot Arm Assembly (upper). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pivot Arm Assembly (Lower) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Steam & Vacuum Lever Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cover & Foot Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pivot Arm Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Steam Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The head steam is hand lever operated while the buck steam and vacuum are foot pedal operated. The improved leverage system and roller bearing pivot assures smoother, faster head operation and a quality finish. Page 5 INSTALLING THE PRESS 1. The Lowboy bracket (PR356) has been installed on the table at the factory. Then assemble the iron rest assembly (PR365, PR398 & PR401) to the shaft of PR356. (See Figure 1) FIGURE 1 (IRON REST) Page 6 INSTALLING THE PRESS (Continued) Steam and Vacuum Connections ­ (See Figure 2) 5. Connect a 3/8 inch steam supply line to the press at a recommended pressure of 88 psi (6 bars). Install a 1/2 inch steam trap suitable for 88 psi (6 bars) in the line. (Example: Cissell Dryset model 2D or larger). 6. 7. FIGURE 2 STEAM & VACUUM CONNECTIONS Page 7 Page 8 Description of the Manual Press The buck of the press is the bottom part of the press upon which the garment is to be placed and pressed. Three foot pedals are located near the floor at the front of the press. The right pedal activates the buck valve which ports upsteam to the buck. Operation of the Manual Press (Allow the press to warm up for 20 min. ) Lay the garment to be pressed on the buck. [. . . ] If there is poor steam flow because the pedal can not travel far enough, then turn the valve lever rod clockwise. Buck Valve ­ This valve is set at the factory and normally would not be adjusted. Once per month add ordinary lubricating oil into the oil holes of the foot pedals. The main pivot of the press head lever is fitted with pillow block bearings that are factory lubricated Lubricate linkage as needed with ordinary oil. General Trouble Shooting ­ Manual Press 1. [. . . ]