User manual CITIZEN WATCH 087

[. . . ] * If the chronograph is being used, measurement stops and it is reset. Stop Warning Function If the watch is left intact in the undercharged state, about 5 days later the second hand will move to the STOP position, indicating that the watch has stopped due to electric power shortage. (Stop warning display) The other hands (hour, minute and 24-hour hands) also stop. Refer to page 25, " In These Cases". Time Setting Warning Function When the watch is recharged by exposing it to light after once stopped, the second hand moves to the SET position, indicating that the watch does not keep correct time. [. . . ] Press button M to set the mode hand to <CHR> and get the chronograph display. At this time, the second hand and the function hand will return to the "0" position. * The hour, minute and 24-hour hands show the present time. 3 While pressing button B continuously, the function hand switches to 1/20 (0. 05) second hand measurement, so read the value at that time. When button B is released, the function hand resumes showing chronograph minutes. While the chronograph is stopped state, pressing button C resets the function hand and the second hand to the 0 position. 2. Each time button A is pressed, it repeatedly starts or stops the chronograph, along with a confirmation sound. How to read each chronograph hand if the measured time when the chronograph is stopped is over 1 minute 1 Read the number of minutes with the function hand 2 Read the number of seconds with the second hand 22 23 Chronograph Split Measurement Pressing button C during chronograph measurement causes the chronograph split time to appear on display with a beep for confirmation. Press button C again, the next chronograph split time is displayed, along with a confirmation sound. The split time display is automatically cancelled after about 10 seconds, and the chronograph returns to the measurement state. During either chronograph split time display or measurement, pressing button A causes the chronograph stop to appear on display. In the chronograph stop state, pressing button C causes the chronograph reset. * During split time measurement or Automatically cancelled after C while split time display, each time about 10 seconds you press button C the next split time is displayed. A C Split Reset Measurement A A Stop IN THESE CASES When Shown the Insufficient Charge Warning Display If the watch is put in the undercharged state during any display mode, it switches to the time display when in other display modes, then the second hand moves to the CHARGE position, indicating insufficiently charged. 7 In such a case, expose the watch to sufficent light for the warning state to be cancelled. (The second hand returns to 1 second movement) T It takes about 30 minutes to complete charging; SE ING WARN from starting to expose the watch to light until this warning state is canceled. The charging time varies depending on the light (light source) that radiates over the watch. 0 M AL 8 2 6 4 OF F 24 ON 18 6 AL M CHR T CAL E L CHR A 24 C ST OP M CHAR 12 GE ME M CAL T 25 When Shown the Stop Warning Display If the watch is left intact in the undercharged state, about 5 days later the second hand will move to the STOP position, indicating that the watch has stopped due to insufficient recharge. 7 In such a case, expose the watch to sufficent light for the warning state to be cancelled. After carrying out sufficient charging, it is necessary ET S ING to reset the alarm time. WARN 0 8 2 6 4 24 ON 18 6 AL CAL AL M CHR T ST OP CAL E CHR AL E L CHR A 26 ST OP M M CHAR M CHR T CHAR 12 When Shown the Time Setting Warning Display If you expose a watch which has stopped once to light and recharge it, the second hand will move to the SET position to let you know that the time is incorrect. In such a case, readjust the hour, minute and 247 hour hands to keep correct time. Without adjusting the time hands after the watch is fully recharged, you cannot use such functions as ET S ING alarm, chronograph, etc. WARN * Be careful because if the watch is not sufficiently charged during the Time Setting Warning Display state, and if light is blocked from it, the second hand will change to the STOP position and the watch will stop running. 0 M AL OF F M AL 8 2 6 4 OF F 24 ON 18 6 GE 12 GE ME ME M CAL T M CAL T 27 CHECKING AND ADJUSTING EACH HAND'S "0" POSITION The watch's display may go wrong due to the effect of static electricity, strong shock, etc. [. . . ] Pay attention to prevent any water from getting inside your watch when the band is washed. Periodic inspection Getting your watch checked once every year or two is recommended to ensure long use and trouble-free operation. SPECIFICATIONS 1. Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multi-Hand Analog Solar Power Watch 2. Time accuracy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 seconds per month (temp. [. . . ]