User manual CITIZEN WATCH C660

[. . . ] 6 2 0 33 30 0 30 (A) 60 24 50 18 12 6 40 30 20 60 20 5 3 9 0 24 8 (C) 1 20 7 (B) 4 15 0 2 10 1 English Please charge the watch fully before use by exposing it to light. When the watch does not operate according to the instruction manual, it is insufficiently charged. Charge the watch for at least 3 hours approximately 20 cm (8 in) away from a fluorescent or incandescent lamp (30 W) as a light source. When charging, do not place the watch too close to the light source to prevent the watch from becoming too hot. [. . . ] · When starting the auto chronograph, the second hand starts moving clockwise in conjunction. Pressing button (B) during measurement of the (B) auto chronograph returns the auto chronograph to Press the race timer initial display. Pressing button (B) while the chronograph is stopped returns the chronograph to the race timer initial setting display. · The second hand rapidly advances to the 12 o'clock position and then stops. · The function hand rapidly advances to the race timer initial setting position and then stops. 24 60 50 20 12. Using the Chronograph The chronograph is able to measure and display time to a maximum of 23 hours, 59 minutes, 59. 99 seconds in 1/100th second units. After 24 hours have elapsed, the chronograph automatically returns to the chronograph reset display. <Normal Chronograph Display> (A) Press 24 50 18 12 6 40 30 20 60 20 <Chronograph Measurement> 1. · The second hand rapidly advances to the 12 o'clock position and stops. Pressing button (A) repeatedly starts and stops the chronograph each time it is pressed. · When starting the chronograph, the second hand starts moving clockwise in conjunction. Split time is displayed for 10 seconds when button (B) is pressed during chronograph measurement. 18 6 40 20 12 30 (B) Press 30 31 · The `SPL" mark flashes in digital display-1 during split time display. Pressing button (B) while the chronograph is stopped, returns the chronograph to the chronograph reset display. · The second and function hand (used as the minute hand for the chronograph) rapidly advance to and stops at the 12 o'clock position. Chronograph reset 24 50 18 12 6 40 60 20 (A) 20 (A) Measurement (B) Stops 30 *1 (B) *2 (A) Split time *1 (B) (A) *1: Returns automatically after timing for 24 hours *2: Returns automatically after 10 seconds 32 33 13. Using the Timer The timer can be set to a maximum of 99 minutes in 1 minute units. When the set time has elapsed, a tone indicating that the set time is up, sounds for about 5 seconds, after which the timer returns to the timer initial setting display. <Timer Initial Setting Display> <Timing using the Timer> 1. When pressing button (A) the timer starts counting (A) down from the time set. Pressing button (A) again during measurement 24 50 18 6 40 12 60 20 <Timer Initial Setting Display> <Setting the Timer> 1. Pull out the crown to the first click (timer setting position) to enter the "minutes" correction state. · "Timer Setting Time (Minutes)" flashes in digital display-2. · When turning the crown to the right (clockwise), correction can be made in the positive direction. When turning the crown to the left (counter clockwise), correction can be made in the negative direction. [. . . ] Cleaning the Watch · Use a soft cloth to wipe off dirt, perspiration and water from the case and crystal. · Use a soft, dry cloth to wipe off perspiration and dirt from the leather band. · To clean a metal, plastic, or rubber watchband, wash away dirt with mild soap and water. Use a soft brush to remove dust and dirt jammed in the gaps in the CAUTION · Do NOT operate the crown or button with wet fingers or when the watch is wet. [. . . ]