User manual DAIKIN BRC1D527

[. . . ] OPERATION MANUAL Remote controller BRC1D527 1 3 6 23 7 8 9 2 1 10 4 12 14 17 25 11 22 16 13 29 15 18 19 20 21 5 33 24 26 35 27 36 37 28 1 30 31 32 34 2 Start 5s 5s 5s 5s + 5s End 2 BRC1D527 Remote controller Operation manual THANK YOU FOR PURCHASING THIS CONTROLLER. Before initial operation, contact your dealer to obtain all details concerning your air conditioning installation. 1. Features and functions The BRC1D527 is a state of the art remote controller that offers full control over your installation. 1 BASIC REMOTE CONTROLLER The basic remote controller functions are: · ON/OFF, · operation mode change-over, · temperature adjustment, · air volume adjustment · air flow direction adjustment. [. . . ] 4 COOLING OPERATION In this mode, cooling will be activated as required by the setpoint or limit temperature. Operation Manual operation In manual operation, the user decides about the settings of the installation. As the controller can be implemented for a wide variety of installations and features, it might occur that you select a function that is not available on your installation; if this is the case, the message will appear. In this mode, heating will be activated as required by the setpoint or limit temperature. Hot start (heat pump types only) At the start of a heating operation, the indoor fan is stopped until a certain indoor heat exchanger temperature is reached and is displayed. This prevents cold air from leaving the indoor unit. Operation manual 5 BRC1D527 Remote controller 4PW16770-1 Use the mode. button to select the desired operation Fan only operation Dry operation Automatic operation Cooling operation Heating operation Press the button to toggle between limit operation and the operations listed above. In limit operation, use the button to select minimum and maximum temperature settings. Use the or buttons to adjust the minimum and maximum temperature settings. button to enable or disable the Operation manual 7 BRC1D527 Remote controller 4PW16770-1 What can the schedule timer do? The concept of the schedule timer is simple, straightforward though powerful. The schedule timer can order 3 actions: 1 switch on the installation at a scheduled time, in combination with a setpoint (exact temperature control) 2 switch off the installation (end of control) 3 switch on the installation at a scheduled time, in limit operation The schedule timer can accept a maximum of 5 actions per day. For each day of the week a maximum of 5 actions can be programmed, totalling a maximum of 35 programmed actions. The action that was programmed first for a certain day is action 1, the last programmed action for a day could be action 1 (in case only one action is programmed for that day) to 5. It is of utmost importance to understand that the number assigned to the programmed action, DOES NOT DETERMINE WHEN the programmed action will be executed. Only the TIME, being a part of the data entered when programming the action, will determine when the programmed action will be executed. OR · switch off the installation (the schedule timer remains enabled and reactivates the installation as programmed); the operation lamp will turn off, cool or heat, whichever is required to keep the room temperature within a specified range (limit operation); and are displayed. The schedule timer will change the operation mode in LIMIT operation only. OR · To be able to verify the programmed actions, you can browse the programmed actions, see below. What will the schedule timer NOT do? The schedule timer will not: · control fan speed, · control air flow direction, · control ventilation mode, · control ventilation amount, · change the operation mode for a scheduled setpoint. The parameters listed above can be set manually, without interfering with the schedule timer. Consult your dealer for more information. What will the schedule timer do? If enabled, the schedule timer will execute the programmed actions. It will order the installation to: · cool or heat, depending on the current operation, if applicable; the setpoint will be displayed, Browsing the programmed actions in the schedule timer (read-out only) Refer to figure 2. Browsing the programmed actions of the schedule timer is a sequential process. The button is used to start browsing, to display the next programmed action or to exit browsing when displaying the last programmed action. BRC1D527 Remote controller 4PW16770-1 Operation manual 8 The button is used to exit browsing at once (without having to scroll through all programmed actions). Press the button to enter the browse mode, the icon appears, will blink. NOTE Browsing always starts on Monday and ends on Sunday. Continue pressing the button until the day of the week indicator displays the current day (not blinking), you have now quit browsing. NOTE The number of times that the button will have to be pressed to quit browsing depends on the number of programmed actions in the schedule timer. Check the icon. [. . . ] is blinking to indicate the selected day, and are steady if actions were copied from Monday to Tuesday, only is displayed if no actions were copied from Monday to Tuesday. 2 I WANT TO EDIT PROGRAMMED ACTIONS Editing programmed actions is easy. Make sure you are not in program mode ( not blinking); if required, press the button to quit program mode. Browse to the programmed actions using the button, select the day and action you want to edit. [. . . ]