User manual DAIKIN BRC1E51A7

[. . . ] WIRED REMOTE CONTROLLER OPERATION MANUAL MODEL BRC1E51A7 Proper Use for Effective Energy Saving Thank you for purchasing the wired remote controller. This manual describes safety precautions required for the use of the product. Read this manual carefully and be sure you understand the information provided before attempting to use the product. Keep this manual where it is readily accessible after reading it through. If another user operates the product in the future, be sure to hand over this manual to the new user. Contents Notices Safety Precautions Items to be Strictly Observed . . . . . . . . . 8 Simple Settings in Direct Buttons for Basic Operation Items Basic Operation Method (Use of Direct Buttons) Cool/Heat/Auto/Fan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] At that time, the other remote controllers with no selection right will follow suit and change the display automatically. Cool/Heat Selection Eligibility The "Cool", "Heat", "Auto" can be set for only the remote controller for which the cooling/heating selection eligibility is set. (The display "Auto" will appear for the heating/cooling simultaneous operation system only. ) The remote controller with the selection eligibility " (without " (Changeover under control) displayed) Other remote controllers (with " " (Changeover under control) displayed) The system will go into the mode set in the remote controller. The system, however, can be switched to fan mode or from "Cool" to "Dry". The remote controller with the selection eligibility " (without " (Changeover under control) displayed) Other remote controllers Set to "Fan" mode. " (with " (Changeover under control) displayed) The system cannot be set to other modes except fan mode. 1. Set to "Cool", "Heat", "Dry", "Auto" mode. 2. 22 English Precautions for Setting Cooling/Heating Selection Eligibility The cooling/heating selection eligibility needs to be set for a single remote controller in the following case. (Cooling/Heating selected operation system) (Cooling/Heating simultaneous operation system) BS unit: The BS unit is used for cooling or heating mode selection. Indoor unit Indoor unit A number of indoor units are connected to a single outdoor unit. Set the cooling/heating/fan selection eligibility in one of the remote controllers. A single BS unit is connected to a number of indoor units. Set the cooling/heating/auto/fan selection eligibility in one of the remote controllers. Key Lock Operation Method Make settings and cancel settings in the basic screen. 1 2 Cool Set temperature 28°C Continue pressing Menu/Enter button for at least four seconds. (During backlight lit) Return Setting Basic screen Cool Set temperature 28°C Return Setting " " will appear. To cancel the key lock mode, continue pressing Menu/Enter button for at least four seconds. (During backlight lit) English 23 Quick Reference of Main Menu Items The main menu has the following items. Setting and display items Description Select normal set temperature or limit control. The airflow direction blade are automatically operated up and down (left and right). The fixed airflow directions are set to five positions. * This function is not available to all models. Reference page Set temp mode changeover Airflow direction setting 27 28 Quick Cooling/Heating On/Off (SkyAir only) Used to set the room to a conformable temperature quickly (unless the system is not in program dry or fan operation). Used to set to "Low" "High" Used to set Automatic, Heat exchange, and Bypass. Operation start time and stop time can be set according to the day of the week. · Operation at set temperature: Normal operation · Operation within set temperature range (between max. temperatures): Limit operation Up to 5 actions can be set for each day. Convenient holiday settings and temporary closure settings are possible. * Clock settings are necessary. * The system goes into schedule timer operation in the previous mode set for the system. 31 Ventilation Ventilation operation settings for total heat exchanger Ventilation rate Ventilation mode 32 33 Timer setting Schedule timer 35 Off reminder timer Used to set each operation period of the system. Possible to set in 10 minute units from 30 to 180 minutes. 42 44 Service Contact/Model Information Used to display the service contact and model information. 24 English Setting and display items Description Used to make LCD contrast adjustment. Display Standard or detailed display Detailed display settings Selectable from the display room temperature, outdoor temperature, system, or without any display items. [. . . ] Holding down the button causes the number to change continuously. Clock setting Year 2008 Month 10 Day 07 Tuesday 12:00 Return Setting Clock setting Year 2008 Month 10 Day 07 Tuesday 12:21 Return Setting Select "Minute" with buttons. The settings confirmation screen will appear. Note: The date can be set between January 1, 2008 and December 31, 2099. English 49 Menu Manipulation 7 Clock setting Is it settled by setting? Yes Return No Setting Press button to select Yes on the settings confirmation screen. Press Menu/Enter button to set the clock and return to the basic screen. * When setting schedule timer, the display return to the settings screens. Caution Daylight Saving Time Caution : The following period has adopted Daylight Saving Timer. [Start] Last Sunday, March AM 2:00 [End] Last Sunday, October AM 3:00 Please consult with your Daikin dealer to change a setup. Language changeover Selectable languages Operation Method 1 MainMenu Convinient functions Setting status list Clock setting Language changeover 2/2 Display the main menu screen. (See page 26. ) Return Setting Press buttons to select Language changeover on the main menu screen and press the Menu/Enter button. 50 English 2 Language changeover Selectable languages English Return Setting Press buttons to select "Language" on the language changeover screen. [. . . ]