User manual DALLEE ELECTRONICS UNION PACIFIC SOUND

[. . . ] IN LOCOMOTIVE DELUXE "UP" STEAM SOUND for various track power by Version 1. 0 CAUTION-THIS DEVICE CAN BE DAMAGED BY STATIC DISCHARGE. DISCHARGE YOURSELF TO AN ELECTRICAL GROUND (OUTLET COVER SCREW) BEFORE REMOVING THIS DEVICE FROM ITS ANTI-STATIC BAG. PLEASE READ INSTRUCTION SHEET COMPLETELY BEFORE ATTEMPTING TO INSTALL AND OPERATE THIS PRODUCT. Save the anti-static bag for possible reuse of storing or shipping the sound unit! can be totally destroyed). [. . . ] These are true Treble and Bass controls and not just tone type controls. If full boost is used, it may be necessary to reduce the volume on that channel to prevent overdrive of the amplifier and speaker. Vol1 (Volume control 1) BASS1 (Bass control 1) - Trbl1 (Treble control 1) all control SPKR1. MISC: Another feature incorporated in this sound system is the ability to turn all sounds off, leaving only the Whistle and Bell to operate. This can be done with the LocoMaticTM Controller by using the ALT & F4 button and is a push on / push off function. Other operators can access this with using function inputs. SPECIFIC INSTRUCTION SHEETS PAGE 3 4 5 6 7 8 9 10 INSTALLATION TYPE overall wiring Conventional DC DCC Receiver Radio Receiver Aristocraft Receiver Synchronization Installation Synchronization Patterns blank Common Whistle signals SOUND INDICATION short . . . . . . . . . . . . . . . . . . . . . . . . All outputs are pulled to ground ("-") to turn the lamps or LED's on. Exceeding the current rating will damage the output driver. Marker Lamps (reverse) #384 (1. 5v) 100 ohms SYNC1 wire Optical Sensor White. . . . . . . . . . . . . . . . . . . . . . . . . Red The optical sensor needs to be mounted so that the front focal distance is 1/8" to 1/4" maximum. With the sound system "ON", the optics can be easily aligned since an exhaust chuff can be heard from any white (reflection) to black (no reflection) transistion. See page 8 for further details. Speaker connections: SPKR - main speaker Red & gray wire pair connect to tender speaker. Backup light #756 (5v) Definitions of connections to be shown on later pages: Red Black White White Black Red Main Board G R Gray Red CONN1: 1 - RED . . . . . . . . . . . . . Motor 1 2 - BLACK. . . . . . . . . Motor 2 3 - WHITE . . . . . . . . . track RF input (for DC operators only) CONN2: 1 - RED . . . . . . . . . . . . . DCC rail 1 . . . . . . . . . . also AC input 2 unlabeled, battery select jumper: on - rechargeable batteries. . . . . . . . . off - standard batteries batt: 1 - RED . . . . . . . . . . . . . DC power "+" 2 - GRAY. . . . . . . . . . . DC power "­" SW1: 1 - RED . . . . . . . . . . . . . switch common 2 - GRAY. . . . . . . . . . . switch open CONN3 - this connector mates to the Volume/Treble/Bass board (not shown) cable. 3 G R G R G R dccF1 1 - Whistle (red) 2 - Bell (gray) dccF2 1 - Cylinder Blow Down (red) 2 - no function (gray) G R G R G R G R G R DC track power installation using batteries & DALLEE controller #755 Connect all wires between boards as shown on page 3. It is important to make all of the previous connections from the right rail to move to the side after the choke. While the drawing shows the motor, previously installed lighting, and a smoke unit, your engine may not contain all of them. You may also wish to change the factory installed lighting to that supplied from the sound cards. Failure to connect other power drawing items to the other side of the choke will result in the LocoMaticTM Controller to not be able to operate the sound system properly. Engine Board White Black Red White CHOKE * DC motor lighting circuits Smoke Unit Right Rail pickup Left Rail pickup The Aux Tender lamp is controlled via the LocoMaticTM Controller's "Aux2" function (Cntrl-Aux buttons together). Red Black White *Larger motors require a larger capacity choke. Chokes: Item 702 - 1. 5 ampere loads Item 703 - 5. 0 ampere loads Gray ON / OFF switch White #566 SPST switch. Switch shown in the OFF position. Lighted car / other engines used in consist preparation. You will know if this is necessary by placing the locomotive / lighted cars on the track and then attempting to blow the Whistle or operate the BELL. If they do not operate with the other items on the track then you need to do the following. We suggest doing this to all lighted cars or engines used in the same consist since it lets the signal stay at it's maximum level. [. . . ] Remember, some paints and other type markers will still reflect the infr-red light. So, just because it's black doesn't guarantee that it will work. The optical coupler comes with laser printed stripes. 1. 25"w x 1"l x 0. 35"h Focus Distance 1/8" - 3/16" Adjustable regulated output from 1. 2 to 6 volts with 1/2 ampere of available output current. The regulator also consumes very little power, so it stays cool under load. [. . . ]