User manual DATALOGIC POWERSCAN 7000 2D IMAGER

[. . . ] PowerScan 7000 2D Imager Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic Scanning"). [. . . ] All other formats remain unaffected. ming Chart on page B-5 Save-- from the Programming Chart on page B-5 of this manual. This exits without saving any Data Format changes. Data Format Editor Commands Send Commands F1 Send all characters followed by "xx" key or function code, starting from current cursor position. Syntax = F1xx (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-4. ) F2 Send "nn" characters followed by "xx" key or function code, starting from current cursor position. Syntax = F2nnxx (nn stands for the numeric value (00-99) for the number of characters and xx stands for the hex value for an ASCII code. See ASCII Conversion Chart (Code Page 1252) on page A-4. ) F3 Send up to but not including "ss" character (Search and Send) starting from current cursor position, leaving cursor pointing to "ss" character followed by "xx" key or function code. Syntax = F3ssxx (ss and xx both stand for the hex values for ASCII codes, see ASCII Conversion Chart (Code Page 1252) on page A-4. ) F4 Send "xx" character "nn" times (Insert) leaving cursor in current cursor position. Syntax = F4xxnn (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-4, and nn is the numeric value (00-99) for the number of times it should be sent. ) E9 Send all but the last "nn" characters, starting from the current cursor position. Syntax = E9nn (nn is the numeric value (00-99) for the number of characters that will not be sent at the end of the message. ) Product Reference Guide 5-3 Data Formatting Move Commands F5 Move the cursor ahead "nn" characters from current cursor position. Syntax = F5nn (nn stands for the numeric value (00-99) for the number of characters the cursor should be moved ahead. ) F6 Move the cursor back "nn" characters from current cursor position. Syntax = F6nn (nn stands for the numeric value (00-99) for the number of characters the cursor should be moved back. ) F7 Move the cursor to the beginning of the data string. Syntax = EA Search Commands F8 Search ahead for "xx" character from current cursor position, leaving cursor pointing to "xx" character. Syntax = F8xx (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-4. ) F9 Search back for "xx" character from current cursor position, leaving cursor pointing to "xx" character. Syntax = F9xx (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-4. ) E6 Search ahead for the first non "xx" character from the current cursor position, leaving cursor pointing to non "xx" character. Syntax = E6xx (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-4. E7 Search back for the first non "xx" character from the current cursor position, leaving cursor pointing to non "xx" character. Syntax = E7xx (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-4. ) Miscellaneous Commands FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. . zz where nn is a count of the number of suppressed characters in the list and xxyy . . (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-4. ) FC Disables suppress filter and clear all suppressed characters. E4 Replaces up to 15 characters in the data string with user specified characters. Syntax = E4nnxx1xx2yy1yy2. . . zz1zz2 where nn is the total count of both characters to be replaced plus replacement characters; xx1 defines characters to be replaced and xx2 defines replacement characters, continuing through zz1 and zz2. FE Compare character in current cursor position to the character "xx. " If characters are equal, increment cursor. [. . . ] Belgium Brazil Canada (French) Czechoslovakia Denmark Finland (Sweden) France Germany/Austria Greece Hungary Israel (Hebrew) Italy Page 2-3 2-3 2-3 2-3 2-3 2-3 2-3 2-3 2-3 2-3 2-3 2-3 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-4 2-5 2-5 2-5 KBDCTY0 KBDCTY1 KBDCTY16 KBDCTY18 KBDCTY15 KBDCTY8 KBDCTY2 KBDCTY3 KBDCTY4 KBDCTY17 KBDCTY19 KBDCTY12 KBDCTY5 KBDCTY14 KBDCTY11 KBDCTY9 KBDCTY20 KBDCTY13 KBDCTY25 KBDCTY26 KBDCTY21 KBDCTY22 KBDCTY10 KBDCTY23 KBDCTY6 KBDCTY27 KBDCTY24 KBDCTY7 Program Keyboard Country Latin America Netherlands (Dutch) Norway Poland Portugal Romania Russia SCS Slovakia Spain Sweden Switzerland (German) Turkey F Turkey Q U. K. Product Reference Guide 10-7 Serial Programming Commands Serial Command # Indicates a numeric entry Selection Setting * Indicates default *Regular Caps Lock Shift Lock Automatic Caps Lock Auto Caps via Num Lock Emulate External Page 2-5 2-5 2-5 2-6 2-6 2-6 2-7 2-7 2-7 2-7 2-7 2-7 KBDSTY0 KBDSTY1 KBDSTY2 KBDSTY6 KBDSTY7 KBDSTY5 Keyboard Style Keyboard *Control + ASCII Off Control + ASCII On Keyboard Modifiers *Turbo Mode Off Turbo Mode On *Numeric Keypad Off Numeric Keypad On Serial Port Connection RS-232 300 BPS 600 BPS 1200 BPS 2400 BPS Baud Rate 4800 BPS 9600 BPS 19200 BPS 38400 BPS 57600 BPS *115200 BPS KBDCAS0 KBDCAS1 KBDTMD0 KBDTMD1 KBDNPS0 KBDNPS1 PAP232 232BAD0 232BAD1 232BAD2 232BAD3 232BAD4 232BAD5 232BAD6 232BAD7 232BAD8 232BAD9 QRGa 2-8 2-8 2-8 2-8 2-8 2-8 2-8 2-8 2-8 2-8 10-8 PowerScan 7000 2D Menu Commands Serial Command # Indicates a numeric entry Selection Setting * Indicates default 7 Data, 1 Stop, Parity Even 7 Data, 1 Stop, Parity None 7 Data, 1 Stop, Parity Odd Page 232WRD3 232WRD0 232WRD6 232WRD4 232WRD1 232WRD7 232WRD5 232WRD2 232WRD8 232LPT### 232CTS0 232CTS1 232XON0 232XON1 232ACK0 232ACK1 2-9 2-9 2-9 2-9 2-9 2-9 2-9 2-9 2-9 2-10 2-11 2-11 2-11 2-11 2-11 2-11 Word Length: Data Bits, Stop Bits, and Parity 7 Data, 2 Stop, Parity Even 7 Data, 2 Stop, Parity None 7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even *8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd RS-232 Receiver Time-out Range 0 - 300 seconds *RTS/CTS Off RTS/CTS On RS-232 Handshaking *XON/XOFF Off XON/XOFF On *ACK/NAK Off ACK/NAK On Output Selections *Off On Off *On Off Low *Medium High Low (1250Hz) Medium (2300hz) *High (2900Hz) *Normal Beep Short Beep Image VGA Beeper - Good Read Beeper Volume Good Read BEPBEP0 BEPBEP1 BEPBEP0 BEPBEP1 BEPLVL0 BEPLVL1 BEPLVL2 BEPLVL3 BEPFQ11250 BEPFQ12300 BEPFQ12900 BEPBIP0 BEPBIP1 3-1 3-1 3-2 3-1 3-1 3-2 3-2 3-2 3-2 3-2 3-2 3-3 3-3 Beeper Pitch Good Read (Frequency) Beeper Duration Good Read Product Reference Guide 10-9 Serial Programming Commands Serial Command # Indicates a numeric entry Selection Off *On *1 Setting * Indicates default Page 3-3 3-3 3-3 3-3 3-4 3-9 3-9 3-9 3-9 3-4 3-4 3-4 3-4 3-4 3-5 3-5 3-5 3-6 3-7 3-7 3-7 3-8 3-8 3-8 3-9 LED - Good Read Number of Beeps Good Read BEPLED0 BEPLED1 BEPRPT BEPRPT# DLYRRD500 DLYRR750 DLYRRD1000 DLYRRD2000 DLYRRD##### DLYGRD0 DLYGRD500 DLYGRD1000 DLYGRD1500 DLYGRD##### TRGMOD0 TRGSTO#### Range 1 - 9 Short (500 ms) *Medium (750 ms) Long (1000 ms) Extra Long (2000 ms) Reread Delay User-Specified Reread Delay Range 0 - 30, 000 ms *No Delay Good Read Delay Short Delay (500 ms) Medium Delay (1000 ms) Long Delay (1500 ms) User-Specified Good Read Delay Range 0 - 30, 000 ms *Manual/Serial Trigger Read Time-Out Trigger Mode (0 - 300, 000 ms) *0 Manual Trigger, Low Power Low Power Time-Out Timer TRGLPT### ( 0 - 300 seconds) *120 Scan Stand Mode Scan Stand Symbol Presentation Mode LEDs Off *LEDs On Range 0-20 (*1) Range 0 - 300, 000 ms TRGMOD4 FNC3 TRGMOD3 TRGPCK0 TRGPCK1 TRGPMS## TRGPTO##### # TRGMOD2 Scan Stand Presentation Presentation LED Timer Presentation Sensitivity Hands Free TimeOut 10-10 PowerScan 7000 2D Menu Commands Serial Command # Indicates a numeric entry Selection Off LED Power Level Setting * Indicates default Page 3-10 3-10 3-10 3-11 3-11 3-11 3-12 3-12 3-12 3-12 3-14 3-14 3-14 3-16 3-16 3-16 3-16 3-16 3-16 3-16 3-17 3-17 3-21 3-21 PWRLDC0 PWRLDC50 PWRLDC100 SCNLED1 SCNLED0 SDRTIM##### # SCNDLY200 SCNDLY400 SCNDLY0 SCNDLY#### SCNAIM0 SCNAIM1 SCNAIM2 DECWIN1 DECWIN0 DECLFT DECRGT DECTOP DECBOT DECMOD0 DECMOD1 DECMOD2 SEQBLK SEQDFT Low (50%) *High (100%) *Lights On Lights Off Range 0 - 999, 999 ms Illumination Lights Imager Time-Out (*120, 000 ms) 200 milliseconds Aimer Delay User-Specified Aimer Delay Aimer Modes 400 milliseconds *Off (no delay) Range 0 - 4, 000 ms Off *Concurrent Interlaced Centering On *Centering Off Left of Centering Window (*40%) Centering Window Right of Centering Window (*60%) Top of Centering Window (*40%) Bottom of Centering Window (*60%) Full Omnidirectional (Default for 2D imagers) Quick Omnidirectional Advanced Linear Decoding (Default for PDF imagers) Enter Sequence Default Sequence Decode Search Mode Output Sequence Editor Product Reference Guide 10-11 Serial Programming Commands Serial Command # Indicates a numeric entry Selection Setting * Indicates default Required On/Not Required *Off On *Off On *Off Set Print Weight (1-7) *Default (4) On *Off *Upright Rotate Clockwise 90 Upside Down Rotate Counterclockwise 90 Prefix/Suffix Selections Page 3-21 3-21 3-21 3-22 3-22 3-22 3-22 3-23 3-23 3-23 3-23 3-24 3-24 3-24 3-24 Require Output Sequence Multiple Symbols No Read Print Weight Video Reverse SEQ_EN2 SEQ_EN1 SEQ_EN0 SHOTGN1 SHOTGN0 SHWNRD1 SHWNRD0 PRTWGT PRTWGT4 VIDREV1 VIDREV0 ROTATN0 ROTATN1 ROTATN2 ROTATN3 VSUFCR PREBK2## PRECL2 PRECA2 SUFBK2## SUFCL2 SUFCA2 RMVFNC0 RMVFNC1 DLYCHR## DLYCRX## Working Orientation Add CR Suffix to All Symbologies Add Prefix Prefix Clear One Prefix Clear All Prefixes Add Suffix Suffix Function Code Transmit Intercharacter Delay User Specified Intercharacter Delay Clear One Suffix Clear All Suffixes *Enable Disable Range 0 - 495 ms Delay Length 4-4 4-5 4-5 4-5 4-5 4-5 4-5 4-5 4-5 4-6 4-7 4-7 (0 - 495 ms) Character to Trigger Delay DLY_XX### 10-12 PowerScan 7000 2D Menu Commands Serial Command # Indicates a numeric entry Selection Interfunction Delay Intermessage Delay Setting * Indicates default Range 0 - 495 ms Range 0 - 495 ms Data Formatter Selections *Default Data Format (None) Page 4-7 4-8 DLYFNC## DLYMSG## DFMDF3 DFMBK3## DFMCL3 DFMCA3 MNUSAV MNUABT DFM_EN0 DFM_EN1 DFM_EN2 VSAF_1 VSAF_2 VSAF_3 5-5 5-5 5-5 5-5 5-5 5-5 5-5 5-5 5-5 5-6 5-6 5-6 Data Format Editor Enter Data Format Clear One Data Format Clear All Data Formats Save Discard Off Data Formatter *On, but Not Required On, Required 1 2 3 Symbologies All Symbologies Off All Symbologies On Default All Codabar Alternate Data Formats All Symbologies ALLENA0 ALLENA1 CBRDFT 6-2 6-2 6-3 6-3 6-3 6-3 6-3 6-4 6-4 6-4 Codabar Settings Codabar Codabar Start/ Stop Char. Validate, But Don't Transmit Validate, and Transmit CBRENA0 CBRENA1 CBRSSX0 CBRSSX1 CBRCK20 CBRCK21 CBRCK22 Product Reference Guide 10-13 Serial Programming Commands Serial Command # Indicates a numeric entry Selection *Off On Setting * Indicates default Page 6-4 6-4 6-4 6-5 6-5 6-5 6-5 6-5 6-5 6-5 6-6 6-6 Codabar Concatenation Codabar Message Length Code 39 CBRCCT0 CBRCCT1 CBRCCT2 CBRMIN## CBRMAX## C39DFT Require Minimum (2 - 60) *4 Maximum (2 - 60) *60 Default All Code 39 Settings Code 39 Code 39 Start/ Stop Char. Off *On *Don't Transmit Transmit *No Check Char. Validate, But Don't C39ENA0 C39ENA1 C39SSX0 C39SSX1 C39CK20 C39CK21 Code 39 Check Char. Transmit Validate, C39CK22 and Transmit 6-6 6-6 6-6 6-7 6-7 6-7 6-7 6-8 6-8 6-9 6-9 6-11 6-11 Code 39 Message Length Code 39 Append Code 32 Pharmaceutical (PARAF) Code 39 Full ASCII Minimum (0 - 48) *0 Maximum (0 - 48) *48 *Off On *Off On *Off On Code 39 Code Page Default All Interleaved C39MIN## C39MAX## C39APP0 C39APP1 C39B320 C39B321 C39ASC0 C39ASC1 C39DCP I25DFT Interleaved 2 of 5 2 of 5 Settings Interleaved 2 of 5 Off *On I25ENA0 I25ENA1 10-14 PowerScan 7000 2D Menu Commands Serial Command # Indicates a numeric entry Selection Setting * Indicates default *No Check Char. Page 6-10 6-10 6-10 6-10 6-10 6-11 6-11 6-11 6-11 6-11 6-11 6-12 6-12 6-12 6-12 6-12 6-13 6-13 6-13 6-13 6-13 6-14 I25CK20 I25CK21 Interleaved 2 of 5 Check Digit Validate, But Don't Transmit Validate, and Transmit I25CK22 I25MIN## I25MAX## C93DFT Settings Off *On Minimum (0 - 80) *0 Maximum (0 - 80) *80 Code 93 Code Page Default All Code 2 of 5 C93ENA0 C93ENA1 C93MIN## C93MAX## C93DCP R25DFT Settings *Off On Minimum (1 - 48) *4 Maximum (1 - 48) *48 Default All IATA Code 2 of 5 R25ENA0 R25ENA1 R25MIN## R25MAX## A25DFT Settings *Off On Minimum (1 - 48) *4 Maximum (1 - 48) *48 Default All Matrix 2 of 5 A25ENA0 A25ENA1 A25MIN## A25MAX## X25DFT Settings Minimum (2 - 80) *4 Maximum (2 - 80) *80 Default All Code 93 Interleaved 2 of 5 Message Length Code 93 Code 93 Code 93 Message Length Code 2 of 5 Code 2 of 5 Code 2 of 5 Message Length IATA Code 2 of 5 IATA Code 2 of 5 IATA Code 2 of 5 Message Length Matrix 2 of 5 Product Reference Guide 10-15 Serial Programming Commands Serial Command # Indicates a numeric entry Selection *Off On Setting * Indicates default Page 6-14 6-14 6-14 6-14 6-14 6-14 6-14 6-15 6-15 6-15 6-15 6-16 6-16 6-16 6-16 6-16 6-17 6-17 6-17 Matrix 2 of 5 Matrix 2 of 5 Message Length Code 11 X25ENA0 X25ENA1 X25MIN## X25MAX## C11DFT Minimum (1 - 80) *4 Maximum (1 - 80) *80 Default All Code 11 Settings Code 11 Code 11 Check Digits Required Code 11 Message Length Code 128 *Off On 1 Check Digit *2 Check Digits Minimum (1 - 80) *4 Maximum (1 - 80) *80 Default All Code 128 C11ENA0 C11ENA1 C11CK20 C11CK21 C11MIN## C11MAX## 128DFT Settings Code 128 ISBT Concatenation Code 128 Message Length Code 128 Code Page Telepen Settings Telepen Telepen Output Telepen Message Length 10-16 Off *On *Off On Minimum (0 - 80) *0 Maximum (0 - 80) *80 Code 128 Code Page (*2) Default All Telepen 128ENA0 128ENA1 ISBENA0 ISBENA1 128MIN## 128MAX## 128DCP## TELDFT 6-17 6-18 6-18 6-18 6-18 6-18 6-18 *Off On *AIM Telepen Output Original Telepen Output Minimum (1 - 60) *1 Maximum (1 - 60) *60 TELENA0 TELENA1 TELOLD0 TELOLD1 TELMIN## TELMAX## PowerScan 7000 2D Menu Commands Serial Command # Indicates a numeric entry Selection Setting * Indicates default Default All Page UPC-A UPC-A Settings UPC-A UPC-A Check Digit UPC-A Number System UPC-A 2 Digit Addenda UPC-A 5 Digit Addenda UPC-A Addenda Required UPC-A Addenda Separator UPC-A/EAN-13 with Extended Coupon Code UPC-E0 Settings UPC-E0 UPC-E0 Expand UPC-E0 Addenda Required UPC-E0 Addenda Separator Off *On *Off On Required *Not Required *On Off Off *On Off *On Off *On *Off On *Off On *Not Required Required Off *On *On Off Default All UPC-E UPADFT UPAENA0 UPAENA1 UPACKX0 UPACKX1 UPANSX0 UPANSX1 UPAAD20 UPAAD21 UPAAD50 UPAAD51 UPAARQ0 UPAARQ1 UPAADS0 UPAADS1 CPNENA1 CPNENA0 UPEDFT UPEEN00 UPEEN01 UPEEXP0 UPEEXP1 UPEARQ1 UPEARQ0 UPEADS1 UPEADS0 6-19 6-19 6-19 6-19 6-19 6-19 6-19 6-20 6-20 6-20 6-20 6-20 6-20 6-20 6-20 6-21 6-21 6-21 6-21 6-21 6-21 6-21 6-22 6-22 6-22 6-22 Product Reference Guide 10-17 Serial Programming Commands Serial Command # Indicates a numeric entry Selection Off *On Off *On Setting * Indicates default Page 6-22 6-22 6-23 6-23 6-23 6-23 6-23 6-23 6-23 6-23 6-24 6-24 6-24 6-24 6-24 6-24 6-24 6-24 6-24 6-25 6-25 6-25 6-25 6-25 6-25 6-26 UPC-E0 Check Digit UPC-E0 Number System UPECKX0 UPECKX1 UPENSX0 UPENSX1 UPEAD21 UPEAD20 UPEAD51 UPEAD50 UPEEN10 UPEEN11 E13DFT 2 Digit Addenda On UPC-E0 Addenda *2 Digit Addenda Off 5 Digit Addenda On *5 Digit Addenda Off UPC-E1 *Off On Default All EAN/ EAN/JAN-13 JAN Settings EAN/JAN-13 EAN/JAN-13 Check Digit EAN/JAN-13 2 Digit Addenda EAN/JAN-13 Addenda Required EAN/JAN-13 Addenda Separator ISBN Translate *Off On Default All EAN/ EAN/JAN-8 JAN 8 Settings Off *On Off *On 2 Digit Addenda On *2 Digit Addenda Off 5 Digit Addenda On *5 Digit Addenda Off *Not Required Required Off *On E13ENA0 E13ENA1 E13CKX0 E13CKX1 E13AD21 E13AD20 E13AD51 E13AD50 E13ARQ0 E13ARQ1 E13ADS0 E13ADS1 E13ISB0 E13ISB1 EA8DFT 10-18 PowerScan 7000 2D Menu Commands Serial Command # Indicates a numeric entry Selection Off *On Off *On Setting * Indicates default Page 6-26 6-26 6-26 6-26 6-26 6-26 6-26 6-26 6-27 6-27 6-27 6-27 6-28 6-28 6-28 6-28 6-28 6-29 6-29 6-29 6-29 6-29 6-29 6-29 6-30 6-30 6-30 EAN/JAN-8 EAN/JAN-8 Check Digit EAN/JAN-8 Addenda EAN/JAN-8 Addenda Required EAN/JAN-8 Addenda Separator MSI MSI EA8ENA0 EA8ENA1 EA8CKX0 EA8CKX1 EA8AD20 EA8AD21 EA8AD50 EA8AD51 EA8ARQ0 EA8ARQ1 EA8ADS0 EA8ADS1 MSIDFT MSIENA0 MSIENA1 MSICHK0 MSICHK1 MSIMIN## MSIMAX## PLSDFT PLSENA0 PLSENA1 PLSMIN## PLSMAX## RSSDFT *2 Digit Addenda Off 2 Digit Addenda On *5 Digit Addenda Off 5 Digit Addenda On *Not Required Required Off *On Default All MSI Settings *Off On *Validate Type 10, but Don't Transmit Validate Type 10 and Transmit Minimum (4 - 48) *4 Maximum (4 - 48) *48 Default All Plessey Settings *Off On Minimum (4 - 48) *4 Maximum (4 - 48) *48 Default All RSS-14 RSS-14 Settings RSS-14 Off *On MSI Check Character MSI Message Length Plessey Code Plessey Code Plessey Message Length RSSENA0 RSSENA1 Product Reference Guide 10-19 Serial Programming Commands Serial Command # Indicates a numeric entry Selection Setting * Indicates default Default All RSS-14 Page RSS Limited Limited Settings RSS Limited Off *On Default All RSS-14 RSS Expanded Expanded Settings RSS Expanded RSS Expanded Msg. Length PosiCode Off *On Minimum (4 - 74) *4 Maximum (4 - 74) *74 Default All PosiCode Settings Off *On PosiCode A and B On A and B and Limited A On *A and B and Limited B On PosiCode Msg. [. . . ]