User manual DAXTEN IP-815 BROCHURE

[. . . ] This product is equipped with a three wire grounding type plug, a plug having a third (grounding) pin. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not use a 3-to-2 prong adapter at the receptacle; use of this type adapter may result in risk of electrical shock and/or damage to this product. Do not locate this product where the cord will be abused by persons walking on it. [. . . ] This address is located on a label on the bottom of the unit, and on the iPAL printed circuit board. The syntax for the MAC address is: nn-nn-nn-nn-nn-nn Setting the IP address using ARP To set the IP address using ARP, connect the 10Base-T connection to your local ethernet network and apply power to the unit. The computer used to set the IP address must be on the same local network as the iPAL. ARP does not work across routed networks. Windows 3. 11, 95 and NT 1. Type the following command: arp -s <IP Address> <MAC Address> Where <IP Address> is the desired IP address for the iPAL and the <MAC address> is the MAC Address of the iPAL. The MAC Address of the iPAL is located on the iPAL's serial number label. Ping the device to confirm that the address has been programmed properly by typing the following: ping <IP Address> If the ping command returns "host not responding" 4 times then the address has not been programmed properly, or the IP Address is incorrect. Delete the entry from the ARP cache by typing: arp -d <IP Address> Note: Due to a bug in the Windows 95 version of ARP you must first have and empty ARP table (seen with arp -a). To empty an arp table type arp -d <ip address> for each entry in the arp table as seen with arp -a. Ping an existing device on your network before setting the IP Address of the IPAL. This device must be a network device other then the one currently being used. Unix, Linux Consult your systems administrator for information on setting an IP Address using ARP. The unit should be pinged after the IP Address has been set to confirm proper operation. iPAL Page 7 2) Configuring Dial-up Networking Use of the Internal modem (if provided) or use of an external modem require the setup of PPP connection using Dial-up Networking. If you computer supports another operating system, consult your network administrator for proper setup details. A) Using Make a New Connection in Dial-up Networking, setup a Dial-Up Networking connection. Now right click and choose properties of the Dial up networking icon you have just created. B) Under the "general" tab, click on configure to set the modem properties. C) Under the modem properties "general" tab, change the maximum speed to 19200 and check the "connect only at this speed" box. After 2 minutes of no activity, iPAL will automatically terminate the session. Should this occur, simply re-connect and re-enter the password. iPAL Upon entering the password, the main menu is displayed: Location Mode = 6 1. # P# S X Outlet Outlet Outlet Outlet 1 2 3 4 Status ON ON ON ON OFF OFF OFF OFF Feedback OK OK OK OK OK OK OK OK Page 10 - Select relay to toggle Pulse relay Setup Exit Enter > Select S to access the setup Menu iPal Setup 1. Circuit Names Location Name Operating Mode Password Pulse Time Web Page Refresh Time Return to the Main Menu Location 6 10 10 Enter > Circuit Names * For All Models * Each circuit (outlet) can be identified with a 20-character name for easy identification. A list of all eight circuits is displayed with the option to change any circuit name. For Models iP-415 and iP-410, enter names for circuits 5-8 if the expansion unit is used. Location Name * For All Models * Each iPAL can be identified by a Location name that appears at the top of each telnet and web page. Select 2 from the Setup Menu to set the Location, up to 20 characters. iPAL Page 11 Operating Mode * Std. Default = 6 * The iPAL supports seven operating modes, which determine how information is displayed, how the inputs are used and how the LED indicators operate. [. . . ] Call Dataprobe Technical Service at (201) 967-8788 to receive a Return Materials Authorization (RMA) Number prior to sending any equipment back for repair. Include all cables, power supplies and proof of purchase with shipment. THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. [. . . ]