Detailed instructions for use are in the User's Guide.
[. . . ] AV SURROUND RECEIVER
AVR-3803/1083
OPERATING INSTRUCTIONS
AMP
REMOTE SENSOR
SIGNAL DIGITAL
SURROUND BACK CH OUTPUT
VOLUME LEVEL
ON / STANDBY
AUTO
INPUT PCM
DTS
SIGNAL DETECT
2 We greatly appreciate your purchase of the AVR-3803/1083. 2 To be sure you take maximum advantage of all the features the AVR-3803/1083 has to offer, read these
instructions carefully and use the set properly. Be sure to keep this manual for future reference, should any questions or problems arise.
"SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE"
2 SAFETY PRECAUTIONS
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
ATTENTION
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). [. . . ] · "PRE" appears on the remote control unit's display.
(1) 2, 3, 4
2
Use the · and ª cursor buttons to display "PUNCH" on the remote control unit, then press the ENTER button. · "SEL" appears on the remote control unit's display.
2, 3, 4
3
Use the · and ª cursor buttons to display the mode for which you want to make the punch through setting, then press the ENTER button. · "SEL" appears on the remote control unit's display.
4
Use the · and ª cursor buttons to display the mode you want to punch through, then press the ENTER button. · "OK" is displayed and the punch through is set.
The display switches as shown below each time the · and ª cursor buttons are pressed. AMP DBS CABLE TV
The display switches as shown below each time the · and ª cursor buttons are pressed. CD CDR VCR2 MD VCR1 TAPE VDP DVD
It is also possible to select the mode directly using the mode buttons.
It is also possible to select the mode directly using the mode buttons.
41
Setting the back light's lighting time
1
Press the power ON/SOURCE button and the OFF button at the same time. · "PRE" appears on the remote control unit's display.
1
DVD
1
2
Use the · and ª cursor buttons to display "BKLT" on the remote control unit, then press the ENTER button. · "05SEC" appears on the remote control unit's display.
2, 3
3
Use the · and ª cursor buttons to adjust the lighting time (3 sec ~ 30 sec), then press the ENTER button. · "OK" is displayed and that lighting time is set.
2, 3
Resetting
(1) Resetting the preset memory
1
Press the power ON/SOURCE button and the OFF button at the same time. · "PRE" appears on the remote control unit's display.
1
DVD
1
2
Use the · and ª cursor buttons to display "RST" on the remote control unit, then press the ENTER button.
2, 3, 4
2, 3, 5
42
3
Use the · and ª cursor buttons to display "PRE" on the remote control unit, then press the ENTER button. · After "SEL" is displayed on the remote control unit's display, the registered preset memory is displayed on the remote control unit's display.
5
When the mode you want to reset is shown on the remote control unit's display, press the ENTER button to reset the preset memory. · The LCD's back light flashes during the resetting operation, and when the operation is completed, "OK" is displayed and the set returns to the normal operating mode.
4
Use the · and ª cursor buttons to select the code to be reset.
(2) Resetting "learned" buttons
1
Press the power ON/SOURCE button and the OFF button at the same time. · "PRE" appears on the remote control unit's display.
1
DVD
1
2
Use the · and ª cursor buttons to display "RST" on the remote control unit's display, then press the ENTER button. · "PRE" is displayed.
2, 3, 4
3
Use the · and ª cursor buttons to display "LRN" on the remote control unit's display, then press the ENTER button. · "SEL" is displayed.
2, 3, 4
4
Use the · and ª cursor buttons to select the mode of the button to be reset, then press the ENTER button. · The LCD's back light flashes during the resetting operation, and when the operation is completed, "OK" is displayed and the set returns to the normal operating mode.
43
(3) Resetting the system call buttons
1
Press the power ON/SOURCE button and the OFF button at the same time. · "PRE" appears on the remote control unit's display.
1
DVD
1
2
Use the · and ª cursor buttons to display "RST" on the remote control unit, then press the ENTER button. · "PRE" appears on the remote control unit's display.
2, 3, 4
3
Use the · and ª cursor buttons to display "CALL" on the remote control unit, then press the ENTER button. · "SEL" appears on the remote control unit's display.
2, 3, 5
4
Press the · and ª cursor buttons to select the system call setting to be reset.
The remote control unit's display switches as shown below each time the · and ª cursor buttons are pressed. SYS CALL 1 SYS CALL 2
5
To reset CALL 1 or CALL 2, select "CALL 1" or CALL 2", then press the ENTER button. · The LCD's back light flashes during the resetting operation, and when the operation is completed, "OK" is displayed and the set returns to the normal operating mode.
44
(4) Resetting the punch through setting
1
Press the power ON/SOURCE button and the OFF button at the same time. · "PRE" appears on the remote control unit's display.
1
DVD
1
2
Use the · and ª cursor buttons to display "RST" on the remote control unit, then press the ENTER button.
3
Use the · and ª cursor buttons to display "PUNCH" on the remote control unit, then press the ENTER button. [. . . ] Even with the high quality multi-channel signals, the recording time is the same as with conventional DTS surround sources. What's more, DTS 96/24 is fully compatible with the conventional DTS surround format, so DTS 96/24 signal sources can be played with a sampling frequency of 48 kHz or 44. 1 kHz on conventional DTS or DTS-ES surround decoders ( 2). 1: A DVD player with DTS digital output capabilities (for CD/LD players, a player with digital outputs for conventional DTS CDs/LDs) and a disc recorded in DTS 96/24 are required. 2: The resolution is 24 or 20 bits, depending on the decoder.
79
System setup items and default values (set upon shipment from the factory)
System setup Speaker Configuration Input the combination of speakers in your system and their corresponding sizes (SMALL for regular speakers, LARGE for fullsize, full-range) to automatically set the composition of the signals output from the speakers and the frequency response. [. . . ]