User manual DENON AVR-1508

[. . . ] AV SURROUND RECEIVER AVR-1508 Owner's Manual Bedienungsanleitung Manuel de l'Utilisateur Manuale delle istruzioni Manual del usuario Gebruiksaanwijzing Bruksanvisning ENGLISH DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA · DECLARATION OF CONFORMITY We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3. Following the provisions of 2006/95/EC and 2004/108/EC Directive. n SAFETY PRECAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: CAUTION · ÜBEREINSTIMMUNGSERKLÄRUNG Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf das sich diese Erklärung bezieht, den folgenden Standards entspricht: EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3. Entspricht den Verordnungen der Direktive 2006/95/EC und 2004/108/EC. To completely disconnect this product from the mains, disconnect the plug from the wall socket outlet. The mains plug is used to completely interrupt the power supply to the unit and must be within easy access by the user. CAUTION: VORSICHT: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] · Select "Large" or "Small" not according to the physical size of the speaker but according to the low frequency reproduction capabilities based on the frequency set at "Crossover Frequency" (vpage 23). · When "Front Speaker" is set to "Small""Subwoofer" is automatically , set to "Yes" . · If "Subwoofer" is set to "No" "Front Speaker" is automatically set to , "Large" . · If "Surround Speaker" is set to "None" "Surround Back Speaker" are , automatically set to "None" . · When using just one surround back speaker, connect it to the left channel (SBL). k ~ A5 Distance Set distance from listening position to speakers. Before making the settings, measure the distance from the listening position to the different speakers. Getting Started Connections Setup Playback Remote Control Information Troubleshooting [Selectable items] Large Small None Surround Speaker Select surround speakers use and size. [Display] 1. Sp 2. In 3. Op Q [Selectable items] Large Small None Speaker Setup Q Surround Back Speaker Select surround back speaker use and size. 8 FL 3. 6m Q [Selectable items] ( Large ( 2spkrs Small 1spkr None ) ) j Subwoofer Mode Setup Select low range signal to be reproduced by subwoofer. 15 SW 3. 6m Subwoofer Select subwoofer use. [Display] Yes No 1. Sp 2. In 3. Op Q Distance measurement Select the speaker you want to set, then set the distance. Set the value closest to the measured distance. [Selectable items] [Variable range] Q Speaker Setup Large : Select this when using large speakers with ample low frequency reproduction capabilities. 0. 0m ~ 18. 0m : Settable in units of 0. 1 meters. NOTE Set the distance between the listening position and the various speakers to no more than 6. 0 meters. 7 SW Mode Norm Small : Select this when using small speakers without ample low frequency reproduction capabilities. : Select this when no subwoofer is connected. [Selectable items] LFE (Normal) : Play low range and LFE signal of channels set to "Small" . LFE+Main : Play low range and LFE signal of all channels. 1spkr : Select the number of surround back speakers. · This can be set when "System Setup" ­ "Speaker Setup" ­ "Subwoofer" is set to "Yes" . · Play music or a movie source and select the mode offering the strongest bass. · Select "LFE+Main" if you want the bass signals to always be produced from the subwoofer. Operations (vpage 21) ENGLISH A6 Crossover Frequency Select crossover frequency from which subwoofer handles low range signal. A7 Test Tone Adjust channel levels to obtain equal volume from all speakers. Operating from the remote control unit Adjusting with the remote control unit using the test tones is only possible in the "Auto" mode and only effective in the STANDARD mode. The adjusted levels for the different modes are automatically stored in the memory. GAdjusting using test tonesH q Press the TEST button on the remote control unit. w Use the o p button to adjust so that the volume is equal for all speakers. e When the adjustments are completed, press the TEST button on the remote control unit again. Getting Started [Display] 1. Sp 2. In 3. Op Q [Display] 1. Sp 2. In 3. Op Q Connections Speaker Setup Q Q Speaker Setup 17 T. Tone T. Tone Yes< 16Cr. Over 80Hz Auto > Setup Q Q [Selectable items] 40Hz 200Hz 60Hz 250Hz : 80Hz 90Hz 100Hz 110Hz 120Hz 150Hz Playback Test Tone On Q Auto-FL Only the portion of the bass sound of the various speakers output from the subwoofer that has a frequency below the frequency set here is output. Set this according to the low frequency reproduction capabilities of the speakers you are using. Test Tone Select test tone playback method. [Selectable items] Auto : Automatically switch speaker from which test tone is output. · When "System Setup" ­ "Speaker Setup" ­ "Surround Back Speaker" setting (vpage 22) is set to "1spkr" the surround back , speaker display is set to "SB" . · Speakers set to "None" in the Speaker Configuration settings are not displayed. · When "Test Tone" is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see page 39. Remote Control Information · The "Crossover Frequency" can be set when there are speakers that have been set to "Small" at "System Setup" ­ "Speaker Setup" or when "Subwoofer" is set to "Yes" (vpage 22). · For speakers set to "Small" sound below the crossover frequency , is cut from the sound output. · Always set the crossover frequency to "80 Hz" When using small . speakers, however, we recommend setting the crossover frequency to a higher frequency. Manual : Manually switch speaker from which test tone is output. Troubleshooting Test Tone Start Press the o button to select "Yes" then press the o p button to select , "Auto" or "Manual" . [. . . ] · The player is connected using the component input connectors, the monitor is connected using the video (yellow) or S-Video output connectors. · High definition (1080i/720p) and progressive (480p/576p) video signals are not down-converted. Most movie software includes copy prevention signals and cannot be copied. Page 10 ~ 16 ­ ­ Cause · HDMI input setting is improper. [. . . ]