Detailed instructions for use are in the User's Guide.
[. . . ] AV SURROUND RECEIVER
AVR-3801
OPERATING INSTRUCTIONS
2 We greatly appreciate your purchase of the AVR-3801. 2 To be sure you take maximum advantage of all the features the AVR-3801 has to offer, read these instructions
carefully and use the set properly. Be sure to keep this manual for future reference, should any questions or problems arise.
"SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE"
1
1
2 SAFETY PRECAUTIONS
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
ATTENTION
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). [. . . ] · "SET UP" appears on the remote control unit's display.
POWER
1
OFF ON / SOURCE
OFF
ON / SOURCE RC-883 REMOTE CONTROL UNIT
TV
CD
CDR/MD/ TAPE RECEIVER
VCR
DBS/CABLE
VDP
DVD
DISPLAY
MENU
2 3
Press the ENTER button.
ENTER
SURR. PARA.
SETUP
TUNING
OSD
RETURN A/B MEMORY
3, 4, 5
CHANNEL
BAND
MODE
VOLUME
TUNING
SHIFT
2, 3, 4, 6, 7
SKIP
+
ENTER
+ CD
SKIP TUNER
SHIFT
MUTING
PHONO
1
CDR/TAPE
2
VDP
3
DVD
Use the D and H cursor buttons to display "RESET" on the remote control unit, then press the ENTER button.
TUNING
ENTER
4
VCR-1
5
VCR-2/V. AUX
6
TV/DBS
7
TV/ VCR
TEST TONE
8 0
SPEAKER
9
+10
OUTPUT
SURROUND
DOLBY/DTS SURROUND DSP SIMU. 5CH / 7CH STEREO
BAND
MODE
SHIFT
6. 1 / 7. 1 SURROUND
DIRECT
STEREO
TUNING
MODE
INPUT
ANALOG EXT. IN
SYSTEM CALL
CALL 1
CALL 2
BACKLIGHT
37
4
Use the D and H cursor buttons to display "RESET PRE" on the remote control unit, then press the ENTER button. · After "SEL PRE" is displayed on the remote control unit's display, the registered preset memory is displayed on the remote control unit's display.
TUNING
ENTER
6
When the mode you want to reset is shown on the remote control unit's display, press the ENTER button to reset the preset memory.
ENTER
SHIFT
BAND
MODE
SHIFT
TUNING
7
Use the D and H cursor buttons to select the code to be reset.
"CONFIRM" is displayed. To reset the preset memory, press the ENTER button while "CONFIRM" is displayed. · "COMPLETE" appears on the remote control unit's display.
ENTER
5
BAND
TUNING
SHIFT
MODE
TUNING
(3) Resetting "learned" buttons
1
Press the power ON/SOURCE button and the OFF button at the same time. · "SET UP" appears on the remote control unit's display.
OFF ON / SOURCE
POWER
1
OFF
ON / SOURCE RC-883 REMOTE CONTROL UNIT
TV
CD
CDR/MD/ TAPE RECEIVER
VCR
DBS/CABLE
VDP
DVD
2 3
Press the ENTER button.
ENTER
DISPLAY
MENU
SURR. PARA.
SETUP
TUNING
OSD
RETURN A/B MEMORY
3, 4, 5
SHIFT
CHANNEL
BAND
MODE
VOLUME
TUNING
2, 3, 4, 5, 6
Use the D and H cursor buttons to display "RESET" on the remote control unit's display, then press the ENTER button. · "RESET PRE" is displayed.
TUNING
ENTER
SKIP
+
ENTER
+ CD
SKIP TUNER
SHIFT
MUTING
PHONO
1
CDR/TAPE
2
VDP
3
DVD
4
VCR-1
5
VCR-2/V. AUX
6
TV/DBS
7
TV/ VCR
TEST TONE
8 0
SPEAKER
9
+10
OUTPUT
BAND
MODE
SURROUND
SHIFT
DOLBY/DTS SURROUND
DSP SIMU.
5CH / 7CH STEREO
TUNING
6. 1 / 7. 1 SURROUND
DIRECT
STEREO
INPUT
MODE ANALOG EXT. IN
SYSTEM CALL
CALL 1
CALL 2
BACKLIGHT
4
Use the D and H cursor buttons to display "RESET LRN" on the remote control unit's display, then press the ENTER button. · "SEL MODE" is displayed, then "TV" appears.
TUNING
ENTER
BAND
MODE
SHIFT
TUNING
6
"CONFIRM" is displayed. To reset the "learned" button for the selected mode, press the ENTER button while "CONFIRM" is displayed.
ENTER
5
Use the D and H cursor buttons to select the mode of the button to be reset, then press the ENTER button.
TUNING
ENTER
SHIFT
BAND
MODE
SHIFT
TUNING
38
(4) All reset function · This function is for resetting all the settings to the factory defaults.
1
Press the power ON/SOURCE button and the OFF button at the same time. "SET UP" appears on the remote control unit's display.
OFF ON / SOURCE
POWER
1
OFF
ON / SOURCE RC-883 REMOTE CONTROL UNIT
TV
CD
CDR/MD/ TAPE RECEIVER
VCR
DBS/CABLE
VDP
DVD
DISPLAY
MENU
SURR. PARA.
SETUP
TUNING
OSD
RETURN A/B MEMORY
2 3
Press the ENTER button.
ENTER
3, 4
CHANNEL
BAND
MODE
VOLUME
TUNING
2, 3, 4, 5
SKIP
+
ENTER
+ CD
SKIP TUNER
SHIFT
MUTING
SHIFT
PHONO
1
CDR/TAPE
2
VDP
3
DVD
4
VCR-1
5
VCR-2/V. AUX
6
TV/DBS
7
8 0
SPEAKER
9
+10
OUTPUT
Use the D and H cursor buttons to display "RESET" on the remote control unit, then press the ENTER button.
TUNING
ENTER
TV/ VCR
TEST TONE
SURROUND
DOLBY/DTS SURROUND DSP SIMU. 5CH / 7CH STEREO
6. 1 / 7. 1 SURROUND
DIRECT
STEREO
INPUT
MODE ANALOG EXT. IN
BAND
MODE
SHIFT
SYSTEM CALL
CALL 1
CALL 2
BACKLIGHT
TUNING
4
Use the D and H cursor buttons to display "RESET ALL" on the remote control unit, then press the ENTER button.
TUNING
ENTER
BAND
MODE
SHIFT
TUNING
5
"CONFIRM" is displayed. To reset, press the ENTER button while "CONFIRM" is displayed. · "BUSY" is displayed during the resetting operation, and "COMPLETE" is displayed once resetting is completed.
ENTER
SHIFT
39
Auto search function
· The set is equipped with a function for searching for the registration number if you do not know the preset code (a 4-digit number) when setting the preset memory.
POWER
1 2
For TV, DBS or CABLE components, turn on the component's power. For CD, MD, TAPE, DVD, VCR and VDP component's, turn on the component's power and load a disc or tape. · "SET UP" appears on the remote control unit's display.
OFF ON / SOURCE
2 6
OFF
ON / SOURCE RC-883 REMOTE CONTROL UNIT
TV
CD
CDR/MD/ TAPE RECEIVER
VCR
DBS/CABLE
VDP
DVD
DISPLAY
MENU
SURR. PARA.
SETUP
TUNING
OSD
RETURN A/B MEMORY
4, 5
CHANNEL
BAND
MODE
VOLUME
TUNING
3, 4, 5, 7
SKIP
+
ENTER
+ CD
SKIP TUNER
SHIFT
MUTING
PHONO
1
CDR/TAPE
2
VDP
3
DVD
4
VCR-1
5
VCR-2/V. AUX
6
TV/DBS
3 4
Press the ENTER button.
ENTER
7
TV/ VCR
TEST TONE
8 0
SPEAKER
9
+10
OUTPUT
SURROUND
SHIFT
DOLBY/DTS SURROUND
DSP SIMU.
5CH / 7CH STEREO
6. 1 / 7. 1 SURROUND
DIRECT
STEREO
INPUT
MODE ANALOG EXT. IN
SYSTEM CALL
CALL 1
CALL 2
BACKLIGHT
Use the D and H cursor buttons to display "AUTOSEARCH" on the remote control unit, then press the ENTER button.
TUNING
ENTER
BAND
MODE
SHIFT
TUNING
5
Use the D and H cursor buttons to display the mode of the component to be searched for on the remote control unit's display, then press the ENTER button. · The registration codes are transmitted in order.
TUNING
ENTER
If you press the power OFF button late at step 6, press the D and H cursor button once to move to the next code or back to the previous code one step at a time. D button: Next code H button: Previous code Auto search resumes when you move ahead from the code at which you stopped.
BAND
MODE
SHIFT
TUNING
6
When the component operates, press the POWER OFF button. · The mode and the registered number appear on the remote control unit's display. [. . . ] In addition, the bit stream format is 100% compatible with conventional DTS signals, so the effect of the Matrix 6. 1 format can be achieved even with 5. 1-channel signal sources. Of course it is also possible to play DTS-ES Matrix 6. 1 encoded sources with a DTS 5. 1-channel decoder.
2
When DTS-ES Discrete 6. 1 or Matrix 6. 1 encoded sources are decoded with a DTS-ES decoder, the format is automatically detected upon decoding and the optimum playing mode is selected. However, some Matrix 6. 1 sources may be detected as having a 5. 1-channel format, so the DTS-ES Matrix 6. 1 mode must be set manually to play these sources. (For instructions on selecting the surround mode, see page 51. ) The DTS-ES decoder includes another function, the DTS Neo:6 surround mode for 6. 1-channel playback of digital PCM and analog signal sources.
2
DTS Neo:6TM surround This mode applies conventional 2-channel signals to the high precision digital matrix decoder used for DTS-ES Matrix 6. 1 to achieve 6. 1channel surround playback. [. . . ]