User manual DENON AVR-591 CODES IR

[. . . ] Be sure to keep this manual for future reference should any questions or problems arise. "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This device complies with Part 15 of the FCC Rules. [. . . ] NOTE: · Note that noise will be output when CDs or LDs recorded in DTS format are played in the "PCM" or "ANALOG" mode. Select the "DTS" mode when playing signals recorded in DTS from a laser disc player or CD player. Note on playing a source encorded with DTS · Noise may be generated at the beginning of playback and while searching during DTS playback in the AUTO mode. If so, play in the DTS mode. · Selecting the AUTO, PCM and DTS modes The mode switches as shown below each time the INPUT MODE button is pressed. AUTO PCM (RF) INPUT MODE DTS (Main unit) (Remote control unit) 33 3 Select the play mode. Example: Stereo STEREO Input mode display · In the AUTO mode AUTO INPUT MODE PCM DTS RF One of these lights, depending on the input signal. ANALOG DIGITAL · In the PCM mode AUTO INPUT MODE PCM DTS RF DIGITAL (Main unit) (Remote control unit) · In the DTS mode AUTO INPUT MODE PCM DTS RF 4 5 Start playback on the selected component. · For operating instructions, refer to the component's manual. Adjust the volume. MASTER VOLUME DIGITAL · When switched to RF in the VDP RF or AUTO mode AUTO INPUT MODE PCM DTS RF DIGITAL · In the ANALOG mode AUTO INPUT MODE PCM DTS RF ANALOG The volume level is displayed on the master volume level display. (Main unit) (Remote control unit) Input signal display · DOLBY DIGITAL INPUTSIGNAL One of these lights, depending on the input signal. The volume can be adjusted within the range of ­60 to 0 to 18 dB, in steps of 1 dB. However, when the channel level is set as described on page 25 or page 42, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume adjustment range is "18 dB -- (Maximum value of channel level)". ) Input mode when playing DTS sources · Noise will be output if DTS-compatible CDs or LDs are played in the "ANALOG" or "PCM" mode. When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to "AUTO" or "DTS". · The recording signals are output to the MULTI ZONE-2 OUT, TAPE and VCR output terminals. 1 2 3 Press the REC/M-ZONE 2 button until "REC OUT SOURCE" appears on the display. REC / M-ZONE 2 (Main unit) Set the input mode according to the source to be played. INPUT MODE (Main unit) Set the surround mode by pressing the DIRECT or STEREO button. · The multichannel digital signals are down-mixed and output to the TAPE and VCR output terminals. STEREO 3 3 or or (Main unit) (Remote control unit) 4 36 Set the recording mode. [3] Outputting a program source to an amplifier, etc. , in a different room (M-ZONE 1 mode) 1 2 3 1 2 Press the M-ZONE 1 button. M-ZONE 1 (Main unit) Select the source you want to output appears on the set's display. FUNCTION (Main unit) Start playing the source to be output. · For operating instructions, refer to the manuals of the respective components. [4] Outputting a program source to an amplifier, etc. , in a different room (M-ZONE 2) Press the REC/M-ZONE 2 button until "M-ZONE 2 SOURCE" appears on the set's display. REC / M-ZONE 2 (Main unit) Select the source you want to record appears on the set's display. · When the AVR-5800 is in the REC OUT mode, the source cannot be output using the M-ZONE 2 buttons on the remote control unit. FUNCTION 1, 2 (Main unit) 1 2 2 Display PHONO CD TUNER AUX DVD / VCR -1 -2 V. AUX MD / VDP TV / DBS TAPE -1 -2 3 Start playing the source to be output. · For operating instructions, refer to the manuals of the respective components. When "M-ZONE 2" is selected for the system setup's multi-zone setting, the source selected here is output from the M-ZONE 2 speaker terminals. The volume can be adjusted and the input source can be selected using the VOLUME UP and VOLUME DOWN buttons on the remote control unit's "M-ZONE 2" page. NOTES: · The signals of the source selected in the M-ZONE-2 mode are also output from the TAPE and VCR recording output terminals. · Digital signals are not output from the MULTI ZONE 1 audio output jacks. 37 Playback using the external input (EXT. IN button on the remote control unit) to switch the external input. EXT. IN (Main unit) (Remote control unit) The playback switches as shown below each time the button is pressed. EXT. [. . . ] Lucasfilm, THX, Home THX, Re-Equalization, Timbre Matching, Adaptive Decorrelation and THX Ultra are trademarks of Lucasfilm Ltd. THX Surround EX In 1999, a new surround system was launched simultaneously with the release of the movie "Star Wars Episode I". "Dolby Digital Surround EX" is a new movie sound track that greatly enhances the sense of spatial expression and the positioning of the surround channel sound. The result is 360 degrees of movement and moving sound effects that seem to pass right over the listener's head. This system was developed jointly by Lucasfilm THX and Dolby Laboratories, fusing Lucasfilm's idea of improving spatial expression and achieving a uniform 360 degree sound positioning with Dolby Laboratories' matrix encoding technology. [. . . ]