Detailed instructions for use are in the User's Guide.
[. . . ] Professional DIGITAL DJ Mixer
DN-X1600
Owner's Manual
ENGLISH
DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA
FCC INFORMATION (For US customers)
1. COMPLIANCE INFORMATION Product Name: DJ Mixer Model Number: DN-X1600 This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. [. . . ] · Press for more than one second to switch V-LINK ON/OFF .
E0 W9 W8 W7 W6 W5 W4 W3 W2 W1
Q0 TIME/BACK button
TIME: This button is used to select whether to change the effects produced using the u BEAT , buttons on the basis of the number of beats or time. BACK: This is used when returning to the previous screen while setting screen operations are being performed.
u i o Q0 Q1 Q2 Q3 Q4 Q5 W0 Q9 Q7 Q8 Q6 R4
y UTILITY/USB A/USB B button
This allows the presets to be set and the system information to be set, changed or referenced. When it is held down for more than a second, the USB mode switching screen is opened, and the USB device mode or USB host mode can be selected.
Q1 EFX SELECT control
This is for selecting the effect to be used. Refer to the effect functions (page 12).
u BEAT
,
buttons
Q2 PARAMETER MIN/MAX control
This is used to adjust the filter cutoff frequency and other effector parameters. The parameters are changed by the effector selected.
(Short) : The beat/time is decreased. (Long) : The beat/time is increased.
Q3 Parameter ON/OFF button
This is used to control the ON and OFF settings of the effect parameters.
Q4 DRY/WET control
Use this to adjust the ratio of original and effected sound.
4
ENGLISH
Q5 Effect ON/OFF button
Sets the EFX effects to ON/OFF.
W4 SPLIT CUE button
There are two headphone monitor modes. SPLIT CUE OFF: The cue signals and master signals can be monitored in stereo. SPLIT CUE ON: The monaural cue signals are heard through the left channel of the headphones, and the monaural master signals through the right channel.
E5 SOURCE
Q6 Channel EFX SEND button
The various set effects can be obtained for the channel audio signal. Multiple channels can be selected.
SEL LN1/LN2/LN3/LN4/USB/P14 controls (channel input selector) These enable any of six inputs to be selected for each of the channels. The same input can be selected for more than one channel.
LINE1 LINE2 LINE3 LINE4
R1 MASTER BALANCE control
Adjusts the L/R balance of the MASTER output.
Getting Started Connections Basic Operations
R2 L/CUE, R/PGM master level meter
One of two modes can be selected for display on this meter. SPLIT CUE ON: The right channel master CUE (monaural) and left channel CUE (monaural) audio levels are displayed.
Q7 Channel CUE buttons Pressing in any or all of CUE buttons routes the respective source to the headphone and meter cue sections. When the CUE button is pressed multiple times, the channels selected by the CUE button are mixed. · The SOLO mode with no signals mixed can also be selected as a preset. Q8 CROSSFADER ASSIGN switches
A, B: The channel source is assigned to A or B of the Crossfader. THRU: Select when you don't assign the channel source into the Crossfader.
USB 1/2 - 7/8 USB P1 - P4 SOURCE SEL CH1 SOURCE SEL CH4
W5 CROSSFADER CONTOUR control
Allows adjusting the "shape" of the Crossfader response from a gentle curve for smooth, long running fades, to the steep pitch required for top performance cut and scratch effects.
R3 SIG/PK indicator
This is the signal/peak meter for the mic input level. Off: No signals input (under 60 dB/FS) Green: Signal input (60 dB/FS to under 20 dB/FS) Orange: Suitable signal input level (20 dB/FS to under 6 dB/FS) Red: Excessively high signal input level (above 6 dB/ FS)
W6 CH FADER CONTOUR control
Adjusts the volume curve response of the channel fader.
Effector Function
W7 CH FADER START switch
This function will start the performance of CD/ Media Player with Ch. Fader automatically is
The desired USB source from USB P1P4 can be selected from USB 1/27/8 and DVS from the utility mode preset control.
E6 CD/PHONO line input selector buttons
These enable the line input of each channel to be selected as CD or PHONO. CD: Rear panel LINE14 CD terminal input PHONO: Rear panel LINE24 PHONO terminal input · LINE1 is only for the CD terminal input.
Q9 CROSSFADER
Controls the relative output level from the summed A and B Mixes. When the fader is at its far left, only the A Mix is heard from the Outputs. As the fader is moved toward the right, the amount of B Mix is increased and the amount of A Mix is decreased. When the fader is centered, equal amounts of A and B Mixes are routed to the Outputs. Fully right is all B Mix at the Outputs.
ON/OFF.
Fader Start
W8 CROSSFADER START switches
Use this to switch the Crossfader Start function ON and OFF.
W9 MIC SEND LEVEL control
This is used to adjust the level at which the mic signals are sent to the master output.
R4 MIDI button
Pressing this button makes the EFX control function as the MIDI controller.
USB
E7 Channel input LEVEL controls
These are used to adjust the levels of the selected inputs.
Utility
E0 Mic EFX INS button
This button enable the various effects to be obtained for the mic input signals.
R5 MIDI parameter control
Controlling each button outputs the MIDI command.
W0 Channel input fader (CH FADER)
Controls the level of the selected Input.
E8 MIDI layer selector buttons
When these buttons are set to ON, the controls of the selected channels function as MIDI controllers.
Specifications
E1 MIC EQ controls
Adjusts the frequency of the mic input.
R6 MIDI function buttons (FUNC1/2/3/4)
Controlling each button outputs the MIDI command. [. . . ] When set to INT, the frequency is synchronized with the System Setting sampling frequency. Power ON USB Mode This selects the USB mode to be used when the power is switched on. DN-X1600 Initialize Returns all of the items for the unit to the factory settings.
with the export files 1 Insert the USB memory devicethe unit's power with into the DN-X1600 or turn on the device already inserted. verify whether the presets are to be called OK is 3 When Settingselected, the preset Audio Setting and MIDI of the export file are called.
· The preset information stored inside the DN-X1600 is not
updated.
memory device is ejected, a screen 4 When the USB user to verify whether to return to prompting the the status before the presets were called appears.
· Cancel cannot be selected.
24
ENGLISH
· BOOTH output
Specifications
(0 dBu = 0. 775 Vrms, 0 dBV = 1 Vrms) n AUDIO · PHONO inputs Stereo x 3 Unbalanced RCA terminal Input impedance: 47 k Level: 40 dBV (10 mV) Signal to Noise ratio: 89 dB · CD inputs Stereo x 5 Unbalanced RCA terminal Input impedance: 10 k Level: 0 dBV Signal to Noise ratio: 100 dB · Equalizer (LINE) Band x 3 Channel equalization adjustment range: HI: , 90 dB to +10 dB MID: , 90 dB to +10 dB LOW: , 90 dB to +6 dB · RETURN inputs Monaural x 2 1/4" TS terminal Input impedance: 10 k Level: 10dBV/0dBV (Default: 10dBV) · MIC inputs Monaural x 2 MIC1: Balanced XLR connectors (1: Ground, 2: Hot, 3: Cold) MIC2: Balanced 1/4" TRS jack (Tip: hot, ring: cold, sleeve: ground) Input impedance: 5 k Level: 60 to 20 dBu EIN: Less than 126 dBu (Rs = 150 ) CMRR: More than 89 dB (1 kHz) · Equalizer (MIC) Band x 2 Adjustment range: HI: 15 to +15 dB LOW: 15 to +15 dB · USB audio inputs Stereo x 4 (monaural x 8) 24 bit, Fs: 44. 1 kHz, 48 kHz, 96 kHz USB B · MASTER output Balanced: Stereo, balanced XLR terminal (1: Ground, 2: Hot, 3: Cold) DA converter: 32-bit 128x oversampling advanced segment converter Load impedance: More than 600 Level: +4dBu (Max. : +24 dBu) Frequency response: 20 Hz to 20 kHz (±0. 5 dB) THD: Less than 0. 05% Crosstalk: Less than 100 dB (1 kHz) Unbalanced: Stereo RCA terminal Load impedance: 10 k Level: 0 dBu (Max. : +20 dBu) · REC output Stereo Unbalanced RCA terminal Load impedance: 10 k Level: 10 dBV (Max. : +10 dBV)
Load impedance: Level: · SEND output Load impedance: Level: · Headphones output Load impedance: Level: · Digital coaxial output · USB audio output n GENERAL USB MIDI I/O: MIDI OUT: Channel level meters: Cue master level meters: Channel Fader: Crossfader: Dimensions: Weight: Supply voltage: Power consumption: Operational temperature: Operational humidity: Storage temperature:
Stereo Balanced 1/4" TRS terminal (Tip: hot; ring: cold, sleeve: ground) More than 600 +4 dBu (Max. : +24 dBu) Monaural x 2 Unbalanced 1/4" TS terminal 10 k 10 dBV (Max. : +10 dBV) Stereo 40 150 mW Stereo RCA terminal, IEC958 Consumer (Fs: 44. 1 kHz, 48 kHz, 96 kHz) Stereo x 4 (monaural x 8) 24 bit, 44. 1 kHz, 48 kHz, 96 kHz USB B IN: 1ch, OUT: 1ch MIDI1. 0, MIDI Clock USB B OUT: 1ch MIDI1. 0, MIDI Clock 5pin DIN PPM 16-point LEDs from 40 to +10 dB, peak display PPM 16-point LEDs from 40 to +10 dB, peak display 60 mm Slim Type fader 45 mm FLEX Fader (Fader Torque Adjustable) 320(W) x 357(D) x 91(H) mm (12"5/8 (W) x 14"1/16 (D) x 3"5/8 (H)) 6. 2 Kg (13. 7 lbs) AC 120 V, 60 Hz (U. S. A. [. . . ]