User manual DIGITECH DIGIDELAY

[. . . ] DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a period of one year (this warranty is extended to a period of six years when the product has been properly registered by mail or through our website). A Return Authorization number may be obtained from DigiTech by telephone. The company shall not be liable for any consequential damage as a result of the product's use in any circuit or assembly. DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without incurring any obligation to install the same on products previously manufactured. 6. The consumer forfeits the benefits of this warranty if the product's main assembly is opened and tampered with by anyone other than a certified DigiTech technician or, if the product is used with AC voltages outside of the range suggested by the manufacturer. [. . . ] The knob's minimum position is the shortest delay time for the given range. The knob's maximum position is the longest delay time for the given range. When 4-TAPE, 5-MOD DLY, or 6-REVERSE is selected, the delay time ranges vary from 10ms - 8 seconds (see Mode Knob for exact ranges). You can increase the delay time by tapping in a longer time using the Tap Tempo delay feature (see Tap Tempo section). The Time knob is disabled when 7-LOOP is selected or when the DigiDelay is in Tap Tempo mode. Mode Knob Selects a delay range, delay type, or the infinite Loop function. The first four mode settings give you ping-pong delay when Out 2 is used in conjunction with Out 1. Select one of the following: 1-10-250 MS - 10 to 250 milliseconds 2-250 MS-1 SEC - 250 milliseconds to 1 second 3-1-4 SEC - 1 to 4 seconds 4-TAPE* - Emulates a vintage tape delay 5-MOD DLY* - A digital delay with chorused repeats 6-REVERSE* - A delay where the repeats are played backwards 7-LOOP - A repeat/hold function that lets you create infinite loops of up to four seconds in length. To increase the time of Tape or Mod Delay types, use the Tap Tempo delay feature. Connecting a guitar cable to this jack supplies battery power even though the Indicator LED may not be lit. To prolong battery life, disconnect all cables from the pedal when not in use. 7. Pedal Release Pins These two pins are spring-loaded hinges that hold the pedal in place. Push these pins in to release the pedal from the pedal chassis exposing the battery compartment. The Pedal is also used for tapping in the delay time when using the Tap Tempo delay feature. Out 1(Mono) Jack Connect this output to a single guitar amplifier when only one amp or mixer channel is being used. When using the Tap Tempo delay feature, the LED will flash at the rate of the delay time. If the LED becomes dim or does not light when the cables are connected, the battery needs to be replaced. 11. Out 2 Jack Connect this output to a second amplifier for ping-pong delay when using one of the first three Mode settings, or Tape or Reverse delay types. Use both this output combined with Out 1 for a more enhanced chorusing effect when using the Modulated Delay. Tap Tempo Delay The DigiDelay's Pedal can be used as a tap-tempo switch for setting the delay time during a live performance. To use the Pedal for tap-tempo, follow these steps: 1. While the delay effect is on, press and hold the Pedal (8) for 3 seconds until the Indicator LED (10) begins flashing. The Time (4) knob is disabled when tap-tempo is active, and the delay cannot be bypassed. [. . . ] CITTM cabinet modeling has to be enabled each time you apply power to the DigiDelay using the procedure outlined above. Battery Replacement 1. Using the tip of a 1/4" guitar cable, push one of the release pins in on either side of the pedal, and remove the pedal from the pedal chassis. Remove the battery from the battery compartment and disconnect the battery cable. Connect a new battery to the battery cable and put it back in the battery compartment. [. . . ]