User manual DIGITECH GSP1101 BROCHURE

[. . . ] GSP1101 Guitar Preamp/ Processor Owner's Manual IMPORTANT SAFETY INSTRUCTIONS WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING: KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner's manual. These symbols warn that there are no user serviceable parts inside the unit. [. . . ] Mid. Width Adjusts how much of the band spectrum above and below the Mid Freq parameter is affected by the Mid parameter. High. Level Adjusts the high-range level (treble) selected with the High Freq parameter (described below). High. Width Adjusts how much of the band spectrum above and below the High Freq parameter is affected by the High parameter. GSP0 Owner's Manual The Edit Effects/Preset Screen FX LOOP / PREAMP LOOP The GSP1101 features a configurable Loop that can be utilized as either an Effects Loop or as a Preamp Loop. As an Effects Loop, the GSP1101 offers a way to connect an external effects device that can be turned on and off within the signal chain. When configured as a Preamp Loop, you can switch between using an external preamp or the internal GSP1101 amp/preamp modeling. GATE A Noise Gate is designed to eliminate noise while you are not playing, or provide an auto volume swell effect. Model Selects between the DigiTech® noise gate or the volume swell effect. Parameters include: GATE Selects the Noise Gate SWELL Selects the Auto Swell effect. Sets the signal strength (Threshold) required to open or close the Noise Gate. Attenuation Sets the Attenuation (amount of noise reduction) parameter. Ranges from 0 to 99. GSP0 Owner's Manual The Edit Effects/Preset Screen CHORUS/FX The Chorus/FX menu in the GSP1101 offers a long list of modulated effects, including Choruses, Flangers, Phasers, Vibrato, Rotary Speaker, Tremolo, Panner, Envelope Filter (auto wah), AutoYaTM, YaYaTM, SynthTalkTM, Step Filter, DOD FX25, Detune, WhammyTM, Pitch Shift, Detune, Harmony Pitch, and Octaver effects. Parameters include: FX. On/Off Turns the selected Chorus/FX effect on or off. Position Places the Chorus/FX effect before the Distortion effect (Pre Amp) or after the Noise Gate effect (Post Amp). After selecting the type of effect in this module, its parameters appear in the in the Chorus/ FX menu, below the Position parameter. The following list describes each Chorus/FX effect and their parameters in more detail: CHORUS A Chorus adds a short delay to your signal. The delayed signal is modulated in and out of tune and then mixed back with the original signal to create a thicker sound. The GSP1101 includes the following Chorus models: Ce ChoRus TC ChoRus ChoRus mulTI ChoRus Based on the classic Boss® CE-2 Chorus Based on the TC Electronic Chorus DigiTech®'s Dual Chorus DigiTech's famous Multi Chorus® The individual Chorus models have the following parameters: Chorus. Model Ce ChoRus TC ChoRus ChoRus mulTI ChoRus Speed Speed Speed Speed Parameters Depth Width Depth Depth Intensity Waveform Waveform Level Level GSP0 Owner's Manual 0 The Edit Effects/Preset Screen FLANGER A Flanger uses the same principle as a Chorus but uses a shorter delay time and adds regeneration (or repeats) to the modulating delay. This results in an exaggerated up and down sweeping motion to the effect. The GSP1101 includes the following Flanger Effect models: FlangeR TRIggeRed FlangeR mXR FlangeR eh FlangeR Flanger. Model FlangeR TRIggeRed FlangeR mXR FlangeR eh FlangeR PHASER The DigiTech® Flanger The DigiTech Triggered Flanger Based on an MXR® Flanger Based on an Electro-Harmonix® Electric Mistress Parameters Speed Speed Speed Rate Depth Sensitivity Width Range Regen LFO Start Regeneration Color Level Level Manual The individual Flanger models have the following parameters: A phaser splits the incoming signal, and then changes the phasing of the signal. This signal is then taken in and out of phase and mixed back in with the original signal. As the phasing changes, different frequencies get canceled resulting in a warm sort of twisting sound. The GSP1101 includes the following Phaser models: phaseR TRIggeRed phaseR mXR phaseR eh phaseR The DigiTech Phaser The DigiTech Triggered Phaser Based on an MXR Phase 100 Based on an Electro-Harmonix Small Stone The individual Flanger models have the following parameters: Phaser. Model phaseR TRIggeRed phaseR mXR phaseR eh phaseR Speed Speed Speed Rate Parameters Depth Sensitivity Intensity Color Regen LFO Start Level Level GSP0 Owner's Manual The Edit Effects/Preset Screen VIBRATO The DigiTech Vibrato effect modulates the pitch of the incoming signal at an even rate. [. . . ] Press the Back button to return to the previous menu and repeat steps 3 and 4 for other global controllers. Press and hold the Back button to return to the Preset screen. GSP0 Owner's Manual Global Functions Merge In > Thru By setting the Merge In>Thru option to ON, incoming MIDI CC and program change messages are routed out of the GSP1101's MIDI Thru jack to other connected MIDI devices. These messages do not pass through the GSP1101 when the Merge In>Thru is set to OFF. Turn the Edit/Select knob until the MIDI menu is selected and press the knob. [. . . ]