User manual DIGITECH HYPERPHASE

[. . . ] Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Unplug this apparatus during lightning storms or when unused for long periods of time. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 11. WARNING:To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. [. . . ] Turn this knob clockwise to increase the speed, and counter-clockwise to decrease the speed. Turn this knob clockwise to increase the depth, and counter-clockwise to decrease the depth. AC Adapter Jack Connect a DigiTech PS200R (9VDC output) power supply to this jack. Regen Knob Controls the amount of regeneration (feedback) in the phaser effect. Turn this knob clockwise to increase the regeneration, and counterclockwise to decrease the regeneration. When 4-RISE/FALL is selected, this knob creates a rising sweep when set between the minimum and 12 o'clock positions, and a falling sweep when set between the 12 o'clock and maximum positions. 1 234 5 11 10 9 6 7 8 5. Type Knob Selects 1 of the 7 different phaser effect types. 4-RISE / FALL - Creates a constant rising phaser sound when the REGEN knob is set between the minimum and 12 o'clock positions, or a constant falling phaser sound when the REGEN knob is set between the 12 o'clock and maximum positions. 5-TRIG UP* - The phaser effect starts at the bottom of its sweep when the trigger threshold is reached. Use the REGEN knob to adjust the trigger threshold sensitivity and SPEED knob to adjust sweep rate. 6-TRIG DOWN* - The phaser effect starts at the top of its sweep when the trigger threshold is reached. Use the REGEN knob to adjust the trigger threshold sensitivity and SPEED knob to adjust sweep rate. 7-STEP - Creates a random square wave phase effect similar to a sample and hold filter on a synthesizer. * Using a distortion pedal before the Hyper Phase may cause inconsistent triggering due to the non-dynamic nature of distorted signals. 6. Connecting a guitar cable to this jack supplies battery power even though the Indicator LED may not be lit. To prolong battery life, disconnect all cables from the pedal when not in use. Pedal Release Pins These two pins are spring-loaded hinges that hold the pedal in place. Push these pins in to release the pedal from the pedal chassis exposing the battery compartment. Out 1(Mono) Jack Connect this output to a single guitar amplifier or mixer channel when only one amp or mixer channel is being used. If the LED becomes dim or does not light when the cables are connected, the battery needs to be replaced. 11. Out 2 Jack Connect this output to a second amplifier or mixer channel for stereo phasing. [. . . ] Connect a new battery to the battery cable and put it back in the battery compartment. Make sure the battery cable does not interfere with the spring or pedal switch arm. Push the opposite pin in and lower the other side of the pedal into place over the depressed pin. When the pedal is properly fastened, both release pins are flush with the outer side of the pedal. Pedal Pedal Switch Arm 9V DC Battery Pedal Release Pin Battery Compartment Spring Pedal Release Pin Pedal Chassis SPECIFICATIONS: · Controls - Speed, Depth, Regen, Type, On/Off Pedal · Jacks - Input, Out 1 (Mono), Out 2 · Input Impedance - 1 MOhms · Output Impedance - 100 Ohms · Power Supply - 9V Alkaline Dry Battery · Power Consumption - 4. 8Watts (w/optional PS200R power supply) · Battery Life - Approximately 4 hours (with continuous usage) · Dimensions - 4 15/16"(L) x 3 1/8"(W) x 2 1/8"(H) · Weight - 1. 38 lbs. [. . . ]