User manual DIGITECH PDS1700

[. . . ] Opening the chassis for any reason will void the manufacturer's warranty. If liquid is spilled on the unit, shut it off immediately and take it to a dealer for service. Disconnect the unit during storms to prevent damage. THE APPARATUS SHALL NOT bE ExPOSED TO DRIPPING OR SPLASHING LIqUID AND NO ObjECT FILLED WITH LIqUID, SUCH AS vASES, SHALL bE PLACED ON THE APPARATUS CLEAN ONLY WITH A DRY CLOTH. DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOvES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT. [. . . ] The Lead FX, Harmony and Reverb/Delay buttons light on the front panel indicating the status of their parameters. Low is the most common setting for Guitar Sensitivity and should provide the guitar input a healthy signal strength indicated by the Guitar Input Signal LED. If your guitar doesn't send a strong enough signal to turn the Guitar Signal LED green, try setting the Guitar Sensitivity to High. Footswitch 1, Footswitch 2, Footswitch 3 Gtr Sensitivity High 23 VL. Pro. Owner's. Manual The. MIDI/Expression. Pedal. Setup. Menu The. MIDI/Expression. Pedal. Setup. Menu CC/PC Channel Harmony Instrument CH Harmony 4-Ch Notes V1 Ch Harmony 4-Ch Notes V2 Ch Harmony 4-Ch Notes V3 Ch Harmony 4-Ch Notes V4 Ch Defines the MIDI CC (Continuous Controller) and PC (Program or Preset Change) Channels being used at the MIDI In and USB ports of the Vocalist® Live Pro. Range: Off, All and 1 to 16 Defines which of the MIDI channels the Vocalist Live Pro will read note data and pitch bend data from for musIQTM MIDI, Chordal, and Notes Harmony Modes. Range: All and 1 to 16 Defines which MIDI Channel the Vocalist Live Pro will read note data and pitch bend data from for Harmony Voice 1 when 4-Channel Notes Harmony Mode is selected. Range: 1 to 16 Defines which MIDI Channel the Vocalist Live Pro will read note data and pitch bend data from for Harmony Voice 2 when 4-Channel Notes Harmony Mode is selected. Range: 1 to 16 Defines which MIDI Channel the Vocalist Live Pro will read note data and pitch bend data from for Harmony Voice 3 when 4-Channel Notes Harmony Mode is selected. Range: 1 to 16 Defines which MIDI Channel the Vocalist Live Pro will read Note Data and Pitch Bend Data from for Harmony Voice 4 when 4-Channel Notes Harmony Mode is selected. Range: 1 to 16 Controller 1 Controller 2 Controller 3 Controller 4 Controller 5 Controller 6 Controller 7 Controller 8 Controller 9 Controller 10 Controller 11 Controller 12 Controller 13 Controller 14 Controller 15 Controller 16 Table Continued Next Page CC/ Expr-Pdl/ Controller Map Maps the specified MIDI Controller to the Expression Pedal, a MIDI CC (CC0 to CC127), or turns the Controller Assignment Off by selecting No CC. Once the Controller Mapping is complete, these defined Controllers can be assigned to Expression Links control functions uniquely for individual presets in the Edit Presets menu. Note that the Controller Mapping to the Expression Pedal corresponds to the Expression Pedal Input on the rear panel, as MIDI Expression Pedals provide CC channel messages. The Preset Menu contains the following Sub-Menus: · · · · · · Edit Edit Edit Edit Edit Edit Pre-Effects Lead Effects Harmony Lexicon® Reverb Lexicon Delay Expression Links Navigate the desired Preset Menu sub-menus and parameters and turn or push the Edit/Select dial to alter or select parameters. In the Edit Preset Menus, when a preset parameter is altered from its stored value, two results occur. A small x appears to the left of the altered parameter or option and the red System Store button LED becomes lit. Note that the Back button does not cancel changes you've made to a preset or menu, but it can cancel the Store procedure once it has begun. After you edit a preset, you must save it with the Store procedure before either changing to another preset or turning off the power to the Vocalist Live Pro, or the unsaved changes you have made to the stored preset will be lost. Copy or Store Preset The Copy and Store functions of the Vocalist Live Pro are essentially the same. When copying a preset, select the desired preset in the Preset Screen and press the Store button. This will allow you to copy the current preset to an alternate location in the User Preset Bank as well as change the preset name. When storing a preset whose characteristics you have altered from the currently saved configuration, the process is the same and includes the ability to store the preset in the same location in the Preset Bank. Note that you can cancel the Store process at any time by pressing the Back button. The Store button now flashes red indicating the Store Procedure is in process. On the Store screen, the first character of the preset's current name flashes. [. . . ] · If the Main Out outputs a signal but the Aux Out does not, check that the Output Mode in the Global I/O Setup menu is set to Aux=Main or Main, Aux Separate. If Main, Aux Separate is selected for the Output Mode, verify that the AuxLead Level and Aux Hrm Level settings are at high enough levels. · Check that when you play your guitar, the Guitar Input Signal Level LED lights green. If it does not light, try changing the GTR Sensitivity to High in the Global I/O Setup menu. [. . . ]