User manual DIGITECH QUAD4
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DIGITECH QUAD4. We hope that this DIGITECH QUAD4 user guide will be useful to you.
Manual abstract: user guide DIGITECH QUAD4
Detailed instructions for use are in the User's Guide.
[. . . ] Pro
gra
m
55
4 IN
R 1:
CG S-DIS SIN ES PROC
TM
ev
2:
Pl
t
3:
Dl
y
4:
GE
Q
dit FX E pare Com
4
O
U
T
M
U
LT
F I-E
FE
C
TS
PR
O
S CE
SO
R
User's Manual
Please visit Digitech Studio Electronics on the World Wide Web at: http://www. digitech. com
IMPORTANT!
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (e. g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. [. . . ] Set DISPERSION low for a dense cluster of reflections during the early portions of DECAY. Simulates the presence of different room materials by controlling the smoothness of reverberations through the course of DECAY. Low DIFFUSION settings are great for simulating hard, flat surfaces while higher DIFFUSION settings can be used to simulate the presence of irregular surfaces in the room such as natural rock masonry or man-made diffusers. Unlike flat surfaces, these materials reflect (diffuse) the sound in many directions because of the irregularity of the surfaces themselves. Selects which crossover type will be used for the Primary and Secondary reverb stages. These two Parameters allow the crossover to be turned On or Off for each reverb stage. When Off, that particular reverb stage will be full bandwidth, otherwise its frequency response is limited by the X-Over Type and Frequency Parameters. Adjusts how quickly the room absorbs the high-frequency reverberations. In a real room, absorptive materials can be used to dampen the natural high-frequency reverberations of the room. High settings of DAMP cause the reverberations to darken tonally and become less defined over the course of DECAY. Low settings cause less dramatic room effects on the tone of the reverberations. This control can be used to darken the response of bright-sounding gated reverbs. Ranges from 100 Hz to 8 kHz in the Gated Reverb and from 100 Hz to 20 kHz in the Stereo Gated Reverb. Controls the length of the gated reverb in milliseconds (much like the DECAY control of a normal reverb). Ranges from 25 milliseconds to 300 milliseconds (or 500 milliseconds on the Stereo Gated Reverb).
Type
Pre Delay
Density
Dispersion
Diffusion
X-Over Type X-Over Frequency Prim & Secd X-Over Prim & Secd Damp
LowPass
Time
Section 3 - Effects and Parameters
Quad 4 User's Manual
17
PARAM. DESCRIPTION
rin R ev g e oo Tan rb m k Ec ho
er av ig G R ed eo ev
b
b er ev R er b b er eo av at er b
ed
Reverbs (continued)
ev
at
ig
. G
er
er
Sp
St
St
St
G
G
R
R
Blend
The BLEND control cross-mixes reverberations from the left side into the right side and vice-versa. This can be used to increase the realism of the simulated room by adding reverberations from different parts of the room to each channel. These two parameters adjust the amount of BLEND for the Primary and Secondary reverb stages. This one control could have been divided among Size and Reflection controls but has been simplified here for easier use. For more natural sounding reverbs, you may also want to decrease the DENSITY setting as DECAY is shortened. Ranges from . 5 to 23 seconds depending on the Reverb Type currently selected. Controls the length (RT60) for the Primary and Secondary reverbaration stages. [. . . ] The display reads:
FACTORY PRG - CHANGED USER PRG - CHANGED
FX EDIT PAGE UTILITY PAGE
11
CC 1
Factory Reset - press[4]
888%kHz m Sec
LEVEL 2
CLIP
CC 2
CHANGED
%kHz %kHz 2m Sec 888m Sec Yes%kHz m Sec
CHANGED CLIP CLIP
CC 3
CC 4
S-DISCTM PROCESSING
MIDI LEVEL 1
LEVEL 3
IN 1 IN 2 IN 3 IN 4
DIGITAL CLIP MODIFIERS
OUT 1 OUT 2 OUT 3 OUT 4
1 2 3 4 5 6 7 8 9 10
CLIP
LEVEL 4
2. If you press the <3> button, the Information line of the display briefly reads: FACTORY RESETTING. . . In extreme situations, the Studio Quad 4 can be reset using a special power-up procedure. This will also completely reset the Studio Quad 4, eliminating any custom settings created by the user. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE DIGITECH QUAD4
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DIGITECH QUAD4 will begin.