User manual DIGITECH XP100

[. . . ] POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated. POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. [. . . ] With the XP-100, you get classic Wah effects, Pitch shifting, Whammy effects, along with a Volume controller and a Chromatic tuner. To keep things quiet, the XP-100 even comes equipped with an adjustable Noise gate. This owner's guide is provided to get you up and going with the XP-100 and use it to its full potential. Front and Rear Panel Controls and Functions 1 2 3 6 7 8 9 10 11 12 4 5 1. 2. Status Display - The Status Display window shows the current information including: bypass, current effect program number, and Chromatic Tuner information. When the XP-100 is in Program mode (Factory or User), the display will either read: 01-29 (Factory) or U1-U6 (User). *Note- A complete listing of all Factory programs is located on the bottom panel of the XP-100. 4. Program UP/(Hold)DOWN Switch - Lets you select programs. Press and hold and the XP-100 will move down through the program menu. BYPASS/(Hold)TUNER Switch - Puts the unit into Bypass by pressing the footswitch once. To select the Tuner, press and hold the footswitch until the display reads: tu, indicating that you are in Tuner mode. Input Level Control - Sets the amount of signal being sent into the unit. The ideal setting for the input control of the XP-100 is to set the input level at a point where the Clip LED indicator occassionally lights. 5. 6. Dry Output - The Dry output of the XP-100 sends only the un-efffected signal out. Mode/(Hold)Program-Gate Calibration - This button is used to put the XP-100 in and out of User mode. The beauty of the the User mode is, that the XP-100 will give you the opportunity to store up to 6 of your favorite factory programs in the same area. This button is also used to calibrate the noise gate threshold of the XP-100. To put the XP-100 in User mode, simply press the <Mode/(Hold) Program> button. To store a Factory program as a User program, the procedure is as follows: First, select the Program to be stored. From here, use the <UP/(Hold)DOWN> footswitch to select which user location. [. . . ] When PF appears, rock the pedal forward and press the <BYPASS> foot switch. SA will next appear in the display to confirm the pedal is now calibrated. Specs A/D Convert - 18bit 128x oversampled D/A Convert - 18bit 128x oversampled Sample Rate - 46. 8 kHz Frequency Response - 20Hz ~ 20 kHz S/N - Greater than 90dB 1/4" Input Jack (1), Output Jacks (2) Externally powered (PS750) DECLARATION OF CONFORMITY Manufacturer's Name: Manufacturer's Address: Digitech 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product Product Name: Product Options: XP-100 All ( with a Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent). conforms to the following product specifications: Safety: EMC: EN 60065 (1993) IEC63 (1985) with Amendments 1, 2, 3 EN 55013: (1990) EN 55020: (1991) Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC as amended by directive 93/68/EEC. [. . . ]