User manual DIGITECH XP200

[. . . ] POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated. POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. [. . . ] The XP-200 will provide you with a vast array of modulation effects in one compact heavy-duty pedal chassis design. Within the XP-200, lies deep and rich digital effects including: Chorus, Flanger, Triggered Flanger, Phaser, Triggered Phaser, Vibrato, Tremolo and Auto Panner, along with a Volume controller and a Chromatic tuner. This guide is provided to get you up and going with the XP-200 and use it to its full potential. Front and Rear Panel Controls and Functions 1 2 3 6 7 8 9 10 11 12 4 5 1. 2. Status Display - The Status Display window shows the current information including: bypass, current effect program, and Chromatic tuner information. When the XP-200 is in program mode (Factory or User), the display will either read: 1-61 (Factory) or U1-U6 (User). *Note - A complete listing all 36 Factory programs is located on the bottom of the XP-200. 4. Program UP/(Hold)DOWN Switch - Lets you select the programs by either pressing once to move up the effect menu, or press and hold to move down the menu. BYPASS/(Hold)TUNER Switch - Puts the unit into Bypass by pressing the footswitch once. To enter Tuner Mode, and hold the footswitch until the display reads: tu indicating that you are in Tuner mode. Expression Pedal - Controls the selected effect (or volume), in real time. Input Level Control - Sets the amount of signal being sent into the unit. The ideal setting for the input control of the XP-200 is to set the input level at a point where the Clip LED indicator occasionally lights. 5. 6. Right Output - This is the right main output of the XP-200, use it alone, or use it in conjunction with the left output to achieve stereo effects. 11. Mode/(Hold)Program - This button is used to engage the User mode for the XP-200. The beauty of the the User mode is that the XP-200 will give you the opportunity to store up to 6 of your favorite Factory programs within the same area. To put the XP-200 in User mode, simply press the Mode button on the front of the unit. To store Factory programs in the User program mode, The procedure is as follows: First, select the Program to be stored. [. . . ] When PF appears, rock the pedal forward and press the <BYPASS> foot switch. SA will next appear in the display to confirm the pedal is now calibrated. Specs A/D Convert - 18bit 128x oversampled D/A Convert - 18bit 128x oversampled Sample Rate - 46. 8 kHz Frequency Response - 20Hz ~ 20 kHz S/N - Greater than 90dB 1/4" Input Jack (1), Output Jacks (2) Externally powered (PS750) DECLARATION OF CONFORMITY Manufacturer's Name: Manufacturer's Address: Digitech 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product Product Name: Product Options: XP-200 All (with a Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent). conforms to the following product specifications: Safety: EN 60065 (1993) IEC63 (1985 with Amendments 1, 2, 3) EN 55013: (1990) EN 55020: (1991) EMC: Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC as amended by directive 93/68/EEC. [. . . ]