User manual DIGITECH XP400

[. . . ] POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated. POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. [. . . ] The XP-400 offers a unique opportunity to add several different reverb types including Spring tank, Plates, Reverse and many others to a great sounding amplifier that may not have an existing reverb unit. In addition to these reverb types, the XP-400 also has a chromatic tuner for quick tunings on stage or in the studio and can act as a volume controller. This owner's guide is provided to get you up and going with the XP-400 and use it to its full potential. Front and Rear Panel Controls and Functions 1 2 3 6 U1-U6 User Program 1- 8 Arena / Hall 10-18 Studio / Room 20-28 Plate 30-38 Spring 40-48 Gated / Reverse Volume 50 7 8 9 10 11 12 4 LEFT / MONO RIGHT 5 1. 2. Status Display - The Status Display window shows the current information including: bypass, current effect program number, and Chromatic Tuner information. When the XP-400 is in Program mode (Factory or User), the display will either read: 1-50 (Factory) or U1-U6 (User). *Note- A complete listing of all Factory programs is located on the bottom panel of the XP-400. 4. Program UP/(Hold)DOWN Switch - Lets you select programs. Press and hold and the XP-400 will move down through the program menu. BYPASS/(Hold)TUNER Switch - Puts the unit into Bypass by pressing the footswitch once. To select the Tuner, press and hold the footswitch until the display reads: tu, indicating that you are in Tuner mode. Input Level Control - Sets the amount of signal being sent into the unit. The ideal setting for the input control of the XP-400 is to set the input level at a point where the Clip LED indicator occasionally lights. 5. 6. Left/Mono Output - This is the this is the Left/Mono output of the the XP-400. MODE/(Hold)PROGRAM - This button is used to put the XP-400 in and out of User mode. The beauty of the the User mode is, that the XP-400 will give you the opportunity to store up to 6 of your favorite factory programs in the same area. This button is also used to calibrate the noise gate threshold of the XP-400. To put the XP-400 in User mode, simply press the <MODE/(Hold) PROGRAM> button. [. . . ] When PF appears, rock the pedal forward and press the <BYPASS> foot switch. SA will next appear in the display to confirm the pedal is now calibrated. Specs A/D Convert - 18bit 128x oversampled D/A Convert - 18bit 128x oversampled Sample Rate - 46. 8 kHz Frequency Response - 20Hz ~ 20 kHz S/N - Greater than 90dB 1/4" Input Jack (1), Output Jacks (2) Externally powered (PS750) DECLARATION OF CONFORMITY Manufacturer's Name: Manufacturer's Address: Digitech 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product Product Name: Product Options: XP-400 All ( with a Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent). conforms to the following product specifications: Safety: EN 60065 (1993) IEC63 (1985) with Amendments 1, 2, 3 EN 55013: (1990) EN 55020: (1991) EMC: Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC as amended by directive 93/68/EEC. [. . . ]